Embedded IDE Link™ TS

Option Sets

What Are Option Sets?

Option sets are preconfigured settings to specify the target configuration for the Altium^® TASKING^® tools. For example, after you set up your target preferences for a TriCore^® configuration, you can use option sets to switch between using an instruction set simulator configuration, two hardware board configurations, or a simulator with some MISRA C^® rule checking.

You can use option sets either:

• To switch between default target configurations, or

• When creating new template projects, to set up an initial configuration that you can choose to modify later

See Tutorial: Using Option Sets for instructions.

The following preconfigured option sets are available.

A notation of "*" indicates the default in the Target Preferences. The processor type for the default configurations below is defined by your TASKING toolchain.

• Infineon^® TriCore^®:

  • * tricore_sim: Default instruction set simulator configuration.

  • tricore_sim_misra: As tricore_sim, but with some example MISRA C rule checking enabled. See also the TriCore MISRA C demo example, tasking_demo_misra.m, with instructions under Embedded IDE Link™ TS Demos.

  • tricore_1796b: Infineon TriCore 1796b hardware configuration.

  • tricore_1766b: Infineon TriCore 1766b hardware configuration.

• Infineon^® C166^®:

  • c166_sim : Default instruction set simulator configuration.

  • c167cr : Phytec kitCON-C167CR serial connection to hardware (_hw) and simulator (_sim) configurations.

  • *c167cs : Phytec phyCORE-C167CS serial connection to hardware (_hw) and simulator (_sim*) configurations.

  • st10f252 : STMicrolectronics MB449 ST10F25x EVA Board serial connection to hardware (_hw) and simulator (_sim) configurations.

  • st10f269 : Phytec phyCORE-ST10F269 serial connection to hardware (_hw) and simulator (_sim) configurations.

  • xc164cm : Infineon^® XC164CM U CAN start kit USB connection to hardware (_hw_u_can) and simulator (_sim_u_can) configurations. See Supported DAS Software.

  • xc167ci: On-board parallel port wiggler connection to the Infineon XC167CI Starter Kit hardware (_hw) and simulator (_sim) configurations.

    xc167ci_hw_usb : USB wiggler connection to the XC167CI

    Note   For xc167ci targets, you must change jumper 501 when switching between USB wiggler and on-board parallel port wiggler. See your board manual for details.

• Renesas^® M16C

  • * m16c_sim: Default instruction set simulator configuration.

  • r8ctiny_sim: Renesas R8C Tiny instruction set simulator configuration.

• ARM^®:

  • * arm_sim: Default instruction set simulator configuration.

  • arm_sim_big_endian: As arm_sim, but in big-endian mode.

• Freescale™ DSP563xx:

  • * dsp563xx_sim: DSP563xx Family, 16-bit memory model, instruction set simulator configuration.

  • dsp566xx_sim: DSP566xx Family instruction set simulator configuration.

• 8051:

  • * i8051_sim: Default, large memory model, no language extensions, floating point, instruction set simulator configuration.

Back to Top

Supported DAS Software

For the XC164CM and certain TriCore hardware like TC1766 and TC1796, you need to download and install the supported DAS software. If your installation of the TASKING toolset did not come with DAS, then you can download the latest DAS software from this URL:

http://www.infineon.com/das.

At the time of writing, the latest tested DAS versions are:

• DAS Edition v2.6.2

• JTAG JDRV LPT Server v2.4.0

Make sure you restart your computer as instructed after DAS installation.

Back to Top

Embedded IDE Link™ TS Menus

Examples