Note: This page has been translated by MathWorks. Please click here

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

Equalize using decision feedback equalizer that updates weights with RLS algorithm

Equalizers

The RLS Decision Feedback Equalizer block uses a decision feedback
equalizer and the RLS algorithm to equalize a linearly modulated baseband
signal through a dispersive channel. During the simulation, the block
uses the RLS algorithm to update the weights, once per symbol. When
you set the **Number of samples per symbol** parameter
to `1`

, the block implements a symbol-spaced equalizer
and updates the filter weights once for each symbol. When you set
the **Number of samples per symbol** parameter to
a value greater than `1`

, the weights are updated
once every *N*^{th} sample,
for a fractionally spaced equalizer.

The `Input`

port accepts a column vector input
signal. The `Desired`

port receives a training sequence
with a length that is less than or equal to the number of symbols
in the `Input`

signal. Valid training symbols are
those symbols listed in the **Signal constellation** vector.

Set the **Reference tap** parameter so it is
greater than zero and less than the value for the **Number
of forward taps** parameter.

The port labeled `Equalized`

outputs the result
of the equalization process.

You can configure the block to have one or more of these extra ports:

`Mode`

input, as described in Reference Signal and Operation Modes in*Communications System Toolbox™User's Guide*.`Err`

output for the error signal, which is the difference between the`Equalized`

output and the reference signal. The reference signal consists of training symbols in training mode, and detected symbols otherwise.`Weights`

output, as described in Adaptive Algorithms in*Communications System ToolboxUser's Guide*.

To learn the conditions under which the equalizer operates in
training or decision-directed mode, see Adaptive Algorithms in *Communications
System Toolbox User's
Guide*.

For proper equalization, you should set the **Reference
tap** parameter so that it exceeds the delay, in symbols,
between the transmitter's modulator output and the equalizer input.
When this condition is satisfied, the total delay, in symbols, between
the modulator output and the equalizer *output* is
equal to

1+(**Reference tap**-1)/(**Number
of samples per symbol**)

Because the channel delay is typically unknown, a common practice is to set the reference tap to the center tap of the forward filter.

**Number of forward taps**The number of taps in the forward filter of the decision feedback equalizer.

**Number of feedback taps**The number of taps in the feedback filter of the decision feedback equalizer.

**Number of samples per symbol**The number of input samples for each symbol.

**Signal constellation**A vector of complex numbers that specifies the constellation for the modulation.

**Reference tap**A positive integer less than or equal to the number of forward taps in the equalizer.

**Forgetting factor**The forgetting factor of the RLS algorithm, a number between 0 and 1.

**Inverse correlation matrix**The initial value for the inverse correlation matrix. The matrix must be N-by-N, where N is the total number of forward and feedback taps.

**Initial weights**A vector that concatenates the initial weights for the forward and feedback taps.

**Mode input port**When you select this check box, the block has an input port that allows you to toggle between training and decision-directed mode. For training, the mode input must be 1, and for decision directed, the mode must be 0. For every frame in which the mode input is 1 or not present, the equalizer trains at the beginning of the frame for the length of the desired signal.

**Output error**When you select this check box, the block outputs the error signal, which is the difference between the equalized signal and the reference signal.

**Output weights**When you select this check box, the block outputs the current forward and feedback weights, concatenated into one vector.

[1] Farhang-Boroujeny, B., *Adaptive
Filters: Theory and Applications*, Chichester, England,
Wiley, 1998.

[2] Haykin, Simon, *Adaptive Filter
Theory*, Third Ed., Upper Saddle River, N.J., Prentice-Hall,
1996.

[3] Kurzweil, Jack, *An Introduction
to Digital Communications*, New York, Wiley, 2000.

[4] Proakis, John G., *Digital Communications*,
Fourth Ed., New York, McGraw-Hill, 2001.

Was this topic helpful?