Rebuffer sequence of inputs
Signal Management / Buffers
The Delay Line block rebuffers a sequence of Mi-by-N matrix inputs into a sequence of Mo-by-N matrix outputs, where Mo is the output frame size you specify in the Delay line size parameter. Depending on whether Mo is greater than, less than, or equal to the input frame size, Mi, the output frames can be underlapped or overlapped. The block always performs frame-based processing and rebuffers each of the N input channels independently.
When Mo > Mi, the output frame overlap is the difference between the output and input frame size, Mo-Mi. When Mo < Mi, the output is underlapped; the Delay Line block discards the first Mi-Mo samples of each input frame so that only the last Mo samples are buffered into the corresponding output frame. When Mo = Mi, the output data is identical to the input data, but is delayed by the latency of the block. Due to the block's latency, the outputs are always delayed by one frame, the entries of which you specify in the Initial conditions parameter (see Initial Conditions).
The output frame period is equal to the input frame period (Tfo=Tfi). The output sample period, Tso, is therefore equal to Tfi/Mo, or equivalently, Tsi(Mi/Mo)
In the most typical use, each output differs from the preceding output by only one sample, as illustrated below for scalar input.
Note that the first output of the block in the example above is all zeros; this is because the Initial Conditions parameter is set to zero.
The Delay Line block's buffer is initialized to the value specified by the Initial conditions parameter. The block outputs this buffer at the first simulation step (t=0). When the block's output is a vector, the Initial conditions can be a vector of the same size, or a scalar value to be repeated across all elements of the initial output. When the block's output is a matrix, the Initial conditions can be a matrix of the same size, a vector (of length equal to the number of matrix rows) to be repeated across all columns of the initial output, or a scalar to be repeated across all elements of the initial output.
In the following ex_delayline_ref2 model, the block rebuffers a two-channel input with a Delay line size of 3.
The first output frame in this example is due to the latency of the Delay Line block; it is all zeros because the Initial conditions parameter is set to zero. Because the input frame size of 4 is larger than the output frame size of 3, only the last three samples in each input frame are propagated to the corresponding output frame. The frame periods of the input and output are the same, and the output sample period is Tsi(Mi/Mo), or 4/3 the input sample period.
Specify the number of rows in output matrix, Mo.
Specify the value of the block's initial output. When the block outputs a vector, the Initial conditions can be a vector of the same size, or a scalar value to be repeated across all elements of the initial output. When the block outputs a matrix, the Initial conditions can be a matrix of the same size, a vector (of length equal to the number of matrix rows) to be repeated across all columns of the initial output, or a scalar to be repeated across all elements of the initial output.
When you select this check box, the input data is not delayed by an extra frame before it is available at the output buffer. Instead, the input data is available immediately at the output port of the block.
When you select this check box, the En_Out port appears on the
block icon. This block uses a circular buffer internally even though
the output is linear. This means that for valid output, data from
the circular buffer has to be linearized. The En_Out port determines
whether or not a valid output needs to be computed based on the value
Boolean input. If the input value to the
En_Out port is
1, the block output is linearized,
and thus is valid. Otherwise, the output is not linearized, and is
invalid. This allows the block to be more efficient when the tapped
Delay Line's output is not required at each sample time.
Note that when the input value to the En_Out port is
the block can give different results depending on the state of the
model. The results can appear to match valid results or can be invalid,
and they cannot be predicted. You should ignore the block output in
all cases when the input to the En_Out port is
This parameter only appears and applies when the Show En_Out port for selectively enabling output parameter is selected. Use this parameter to specify the block output at those time steps when the internal state buffer is not being linearized to output valid data.
When you do not select this check box, the block memory is free to be used by other parts of the model, and the signal on the output port is invalid. When you select this check box, the most recent valid value is held on the output port, and slightly more memory is used by the block.
Specify how the block treats sample-based M-by-1 column vectors and unoriented sample-based vectors of length M. You can select one of the following options:
One channel — When
you select this option, the block treats M-by-1
and unoriented sample-based inputs as a column vector (one channel).
M channels (this choice will be removed
– see release notes) — When you select
this option, the block treats M-by-1 and unoriented
sample-based inputs as a 1-by-M row vector. Because
the block always does frame-based processing, the block interprets
the 1-by-M row vector as M individual
Note: This parameter will be removed in a future release. At that time, the Delay Line block will always perform frame-based processing.
|Port||Supported Data Types|
|Buffer||DSP System Toolbox|