Documentation

This is machine translation

Translated by Microsoft
Mouseover text to see original. Click the button below to return to the English verison of the page.

Note: This page has been translated by MathWorks. Please click here
To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

Set Output Voltage and Make Measurements from a Keysight® AgE3633A DC Power Supply using the IVI-C Driver

This example shows how to initialize the driver, read a few properties of the driver, set output voltage, enable all outputs and measure the output voltage, disable all outputs and measure the output voltage by using Keysight Technologies E3633A DC power supply and output the result in MATLAB®.

Requirements

This example requires the following:

  • Keysight IO libraries version 17.1 or newer

  • Keysight E36xx DC Power Supply IVI version 1.2.0.0 or newer

Enumerate Available IVI-C Drivers on the Computer

This enumerates the IVI drivers that have been installed on the computer.

IviInfo = instrhwinfo('ivi');
IviInfo.Modules
ans = 

  Columns 1 through 6

    'Ag33220'    'Ag3352x'    'Ag34410'    'Ag34970'    'Ag532xx'    'AgAC6800'

  Columns 7 through 11

    'AgE36xx'    'AgInfiniiVision'    'AgMD1'    'AgRfSigGen'    'AgXSAn'

  Columns 12 through 13

    'KtRFPowerMeter'    'rsspecan'

Create MATLAB Instrument Driver And Connect to the Instrument

% Create the MATLAB instrument driver
makemid('AgE36xx','AgE3633A.mdd')

% Use icdevice with the MATLAB instrument driver name and instrument's
% resource name to create a device object. In this example the instrument
% is connected by GPIB at board index 0 and primary address 1.
myInstrument = icdevice('AgE3633A.mdd', 'GPIB0::01::INSTR','optionstring','simulate=true');

% Connect driver instance
connect(myInstrument);

Attributes and Variables Definition

% These values are defined in the driver's header file 'AgE36xx.h'
IVI_ATTR_BASE = 1000000;
IVI_CLASS_ATTR_BASE = IVI_ATTR_BASE + 250000;
AGE36XX_ATTR_VOLTAGE_LEVEL = IVI_CLASS_ATTR_BASE + 1;
AGE36XX_VAL_MEASURE_VOLTAGE = 1;

Get General Device Properties

Query information about the driver and instrument

DriverIdentification = get(myInstrument,'Inherentiviattributesdriveridentification');
InstrumentIdentification = get(myInstrument,'Inherentiviattributesinstrumentidentification');
Utility = get(myInstrument, 'Utility');
Revision = invoke(Utility, 'revisionquery');
Vendor = get(DriverIdentification, 'Specific_Driver_Vendor');
Description = get(DriverIdentification, 'Specific_Driver_Description');
InstrumentModel = get(InstrumentIdentification, 'Instrument_Model');
FirmwareRev = get(InstrumentIdentification, 'Instrument_Firmware_Revision');

% Print the queried driver properties
fprintf('Revision:        %s\n', Revision);
fprintf('Vendor:          %s\n', Vendor);
fprintf('Description:     %s\n', Description);
fprintf('InstrumentModel: %s\n', InstrumentModel);
fprintf('FirmwareRev:     %s\n', FirmwareRev);
fprintf(' \n');
Revision:        1.2.1.0 
Vendor:          Agilent Technologies
Description:     IVI driver for the Agilent E36xx family of programmable power supplies [Compiled for 64-bit.]
InstrumentModel: E3633A
FirmwareRev:     Sim1.2.1.0
 

Set Output Voltage

Configuration = get(myInstrument, 'Configuration');
invoke(Configuration, 'configurevoltagelevel', 'Output1', 1.23);
fprintf('Output 1 set to: 1.23 Volts \n');
Output 1 set to: 1.23 Volts 

Enable All Outputs and Measure the Output Voltage

Outputs = get(myInstrument, 'Outputs');
set(Outputs, 'Enabled', true);
fprintf('All outputs enabled \n');

% The measured voltage should read as the set value.
Action = get(myInstrument, 'Action');
MeasVal = invoke(Action, 'measure', 'Output1', AGE36XX_VAL_MEASURE_VOLTAGE);
fprintf('Output 1 Measurement = %.4g Volts\n', MeasVal);
All outputs enabled 
Output 1 Measurement = 1.23 Volts

Disable All Outputs and Measure the Output Voltage

set(Outputs, 'Enabled', false);
fprintf('All outputs disabled\n');

% Since all outputs have been disabled, the measured voltage should be 0.
MeasVal = invoke(Action, 'measure', 'Output1', AGE36XX_VAL_MEASURE_VOLTAGE);
fprintf('Output 1 Measurement = %.4g Volts\n\n', MeasVal);
All outputs disabled
Output 1 Measurement = 0 Volts

Display Any Errors from the Driver

% If there are any errors, query the driver to retrieve and display them.
ErrorNum = 1;
while (ErrorNum ~= 0)
    [ErrorNum, ErrorMsg] = invoke(Utility, 'errorquery');
    fprintf('ErrorQuery: %d, %s\n', ErrorNum, ErrorMsg);
end
ErrorQuery: 0, No error. 

Disconnect the Device Object and Clean Up

disconnect(myInstrument);
% Remove instrument objects from memory.
delete(myInstrument);

Additional Information:

This example shows setting output voltage and making measurements on a DC power supply using the IVI driver. Once the measured voltage is retrieved from the instrument, MATLAB can be used to visualize and perform analyses on the data using the rich library of functions in the Signal Processing Toolbox™ and Communications Systems Toolbox™. Using Instrument Control Toolbox™, it is possible to automate control of instruments, and, build test systems that use MATLAB to perform analyses that may not be possible using the built-in capability of the hardware.

Was this topic helpful?