Note: This page has been translated by MathWorks. Please click here

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

Wideband receive array

Transmitters and Receivers

`phasedtxrxlib`

The Wideband Receive Array block receives wideband plane waves incident on the elements of a sensor array. The block divides the input signal into subbands and then applies a phase shift in each subband according to the incident direction. The resulting subband signals are then combined to form the output.

**Signal Propagation speed (m/s)**Specify the propagation speed of the signal, in meters per second, as a positive scalar. You can use the function

`physconst`

to specify the speed of light.**Inherit sample rate**Select this check box to inherit the sample rate from upstream blocks. Otherwise, specify the sample rate using the

**Sample rate**parameter.**Sample rate**Specify the signal sampling rate (in hertz) as a positive scalar. This parameter appears only when the

**Inherit sample rate**parameter is not selected.**Assume modulated input**Select this check this box to indicate that the input signal is demodulated at a carrier frequency.

**Carrier frequency**This parameter appears when the

**Assume modulated input**check box is selected. The parameter specifies the carrier frequency, in hertz, as a positive scalar.**Number of subbands**Number of processing subbands, specified as a positive integer.

**Enable weights input**Select this check box to specify array weights using the input port

`W`

. The input port appears only when this box is checked.**Simulate using**Block simulation method, specified as

`Interpreted Execution`

or`Code Generation`

. If you want your block to use the MATLAB^{®}interpreter, choose`Interpreted Execution`

. If you want your block to run as compiled code, choose`Code Generation`

. Compiled code requires time to compile but usually runs faster.Interpreted execution is useful when you are developing and tuning a model. The block runs the underlying System object™ in MATLAB. You can change and execute your model quickly. When you are satisfied with your results, you can then run the block using

`Code Generation`

. Long simulations run faster than they would in interpreted execution. You can run repeated executions without recompiling. However, if you change any block parameters, then the block automatically recompiles before execution.When setting this parameter, you must take into account the overall model simulation mode. The table shows how the

**Simulate using**parameter interacts with the overall simulation mode.When the Simulink

^{®}model is in`Accelerator`

mode, the block mode specified using**Simulate using**overrides the simulation mode.For more information, see Choosing a Simulation Mode (Simulink) from the Simulink documentation.**Acceleration Modes**Block Simulation Simulation Behavior `Normal`

`Accelerator`

`Rapid Accelerator`

`Interpreted Execution`

The block executes using the MATLAB interpreter. The block executes using the MATLAB interpreter. Creates a standalone executable from the model. `Code Generation`

The block is compiled. All blocks in the model are compiled.

**Specify sensor array as**Specify sensor element or sensor array. A sensor array can also contain subarrays or be a partitioned array. This parameter can also be expressed as a MATLAB expression.

**Types**`Single element`

`Array (no subarrays)`

`Partitioned array`

`Replicated subarray`

`MATLAB expression`

**Geometry**Specify the array geometry as one of the following:

`ULA`

— Uniform linear array`URA`

— Uniform rectangular array`UCA`

— Uniform circular array`Conformal Array`

— arbitrary element positions

**Number of elements**Number of array elements.

Number of array elements, specified as a positive integer. This parameter appears when the

**Geometry**is set to`ULA`

or`UCA`

. If**Sensor Array**has a`Replicated subarray`

option, this parameter applies to the sub-array.**Array size**This parameter appears when

**Geometry**is set to`URA`

. When**Sensor Array**is set to`Replicated subarray`

, this parameter applies to the subarrays.Specify the size of the array as a positive integer or 1-by-2 vector of positive integers.

If

**Array size**is a 1-by-2 vector, the vector has the form`[NumberOfArrayRows,NumberOfArrayColumns]`

.If

**Array size**is an integer, the array has the same number of rows and columns.

For a URA, elements are indexed from top to bottom along a column and continuing to the next columns from left to right. In this figure, an

**Array size**of`[3,2]`

produces an array of three rows and two columns.**Element spacing (m)**This parameter appears when

**Geometry**is set to`ULA`

or`URA`

. When**Sensor Array**has the`Replicated subarray`

option, this parameter applies to the subarrays.For a

`ULA`

, specify the spacing, in meters, between two adjacent elements in the array as a scalar.For a

`URA`

, specify the element spacing of the array, in meters, as a 1-by-2 vector or a scalar. If**Element spacing**is a 1-by-2 vector, the vector has the form`[SpacingBetweenRows,SpacingBetweenColumns]`

. For a discussion of these quantities, see`phased.URA`

. If**Element spacing**is a scalar, the spacings between rows and columns are equal.

**Array axis**This parameter appears when the

**Geometry**parameter is set to`ULA`

or when the block only supports a ULA array geometry. Specify the array axis as`x`

,`y`

, or`z`

. All ULA array elements are uniformly spaced along this axis in the local array coordinate system.**Array normal**,This parameter appears when you set

**Geometry**to`URA`

or`UCA`

. Specify the**Array normal**as`x`

,`y`

, or`z`

. All URA and UCA array elements are placed in the*yz*,*zx*, or*xy*planes, respectively, of the array coordinate system.**Radius of UCA (m)**Radius of a uniform circular array specified as a positive scalar. Units are meters.

This parameter appears when the

**Geometry**is set to`UCA`

.**Taper**Tapers, also known as

*element weights*, are applied to sensor elements in the array. Tapers are used to modify both the amplitude and phase of the transmitted or received data.This parameter applies to all array types, but when you set

**Sensor Array**to`Replicated subarray`

, this parameter applies to subarrays.For a

`ULA`

or`UCA`

, specify element tapering as a complex-valued scalar or a complex-valued 1-by-*N*row vector. In this vector,*N*represents the number of elements in the array. If**Taper**is a scalar, the same weight is applied to each element. If**Taper**is a vector, a weight from the vector is applied to the corresponding sensor element. A weight must be applied to each element in the sensor array.For a

`URA`

, specify element tapering as a complex-valued scalar or complex-valued*M*-by-*N*matrix. In this matrix,*M*is the number of elements along the*z*-axis, and*N*is the number of elements along the*y*-axis.*M*and*N*correspond to the values of`[NumberofArrayRows,NumberOfArrayColumns]`

in the**Array size**matrix. If`Taper`

is a scalar, the same weight is applied to each element. If**Taper**is a matrix, a weight from the matrix is applied to the corresponding sensor element. A weight must be applied to each element in the sensor array.For a

`Conformal Array`

, specify element tapering as a complex-valued scalar or complex-valued 1-by-*N*vector. In this vector,*N*is the number of elements in the array as determined by the size of the**Element positions**vector. If**Taper**is a scalar, the same weight is applied to each element. If the value of**Taper**is a vector, a weight from the vector is applied to the corresponding sensor element. A weight must be applied to each element in the sensor array.

**Element lattice**This parameter appears when

**Geometry**is set to`URA`

. When**Sensor Array**is set to`Replicated subarray`

, this parameter applies to the subarray.Specify the element lattice as

`Rectangular`

or`Triangular`

`Rectangular`

— Aligns all the elements in row and column directions.`Triangular`

— Shifts the even-row elements of a rectangular lattice toward the positive-row axis direction. The displacement is one-half the element spacing along the row dimension.

**Element positions (m)**This parameter appears when

**Geometry**is set to`Conformal Array`

. When**Sensor Array**is set to`Replicated subarray`

, this parameter applies to subarrays.Specify the positions of conformal array elements as a 3-by-

*N*matrix, where*N*is the number of elements in the conformal array. Each column of**Element positions (m)**represents the position of a single element, in the form`[x;y;z]`

, in the array’s local coordinate system. The local coordinate system has its origin at an arbitrary point. Units are in meters.**Element normals (deg)**This parameter appears when

**Geometry**is set to`Conformal Array`

. When**Sensor Array**is set to`Replicated subarray`

, this parameter applies to subarrays.Specify the normal directions of the elements in a conformal array as a 2-by-

*N*matrix or a 2-by-1 column vector in degrees. The variable*N*indicates the number of elements in the array. If**Element normals (deg)**is a matrix, each column specifies the normal direction of the corresponding element in the form`[azimuth;elevation]`

, with respect to the local coordinate system. The local coordinate system aligns the positive*x*-axis with the direction normal to the conformal array. If**Element normals (deg)**is a 2-by-1 column vector, the vector specifies the same pointing direction for all elements in the array.You can use the

**Element positions (m)**and**Element normals (deg)**parameters to represent any arrangement in which pairs of elements differ by certain transformations. You can combine translation, azimuth rotation, and elevation rotation transformations. However, you cannot use transformations that require rotation about the normal.**Subarray definition matrix**This parameter appears when

**Specify sensor array as**is set to`Partitioned array`

.Specify the subarray selection as an

*M*-by-*N*matrix.*M*is the number of subarrays and*N*is the total number of elements in the array. Each row of the matrix corresponds to a subarray and each entry in the row indicates whether or not an element belongs to the subarray. When the entry is zero, the element does not belong the subarray. A nonzero entry represents a complex-valued weight applied to the corresponding element. Each row must contain at least one nonzero entry.The phase center of each subarray is its geometric center.

**Subarray definition matrix**and**Geometry**determine the geometric center.**Subarray steering method**This parameter appears when the

**Specify sensor array as**parameter is set to`Partitioned array`

or`Replicated subarray`

.Specify the subarray steering method as either

`None`

`Phase`

`Time`

`Custom`

Selecting

`Phase`

or`Time`

opens the`Steer`

input port on the Narrowband Receive Array, Narrowband Transmit Array, Wideband Receive Array, Wideband Transmit Array blocks, Constant Gamma Clutter, and GPU Constant Gamma Clutter blocks.Selecting

`Custom`

opens the`WS`

input port on the Narrowband Receive Array, Narrowband Transmit Array, Wideband Receive Array, Wideband Transmit Array blocks, Constant Gamma Clutter, and GPU Constant Gamma Clutter blocks.**Phase shifter frequency (Hz)**This parameter appears when you set

**Sensor array**to`Partitioned array`

or`Replicated subarray`

and you set**Subarray steering method**to`Phase`

.Specify the operating frequency, in hertz, of phase shifters to perform subarray steering as a positive scalar.

**Number of bits in phase shifters**This parameter appears when you set

**Sensor array**to`Partitioned array`

or`Replicated subarray`

and you set**Subarray steering method**to`Phase`

.The number of bits used to quantize the phase shift component of beamformer or steering vector weights. Specify the number of bits as a non-negative integer. A value of zero indicates that no quantization is performed.

**Subarrays layout**This parameter appears when you set

**Sensor array**to`Replicated subarray`

.Specify the layout of the replicated subarrays as

`Rectangular`

or`Custom`

.**Grid size**This parameter appears when you set

**Sensor array**to`Replicated subarray`

and**Subarrays layout**to`Rectangular`

.Rectangular subarray grid size, specified as a single positive integer or a positive integer-valued 1-by-2 row vector.

If

**Grid size**is an integer scalar, the array has an equal number of subarrays in each row and column. If**Grid size**is a 1-by-2 vector of the form`[NumberOfRows, NumberOfColumns]`

, the first entry is the number of subarrays along each column. The second entry is the number of subarrays in each row. A row is along the local*y*-axis, and a column is along the local*z*-axis. The figure here shows how you can replicate a 3-by-2 URA subarray using a**Grid size**of`[1,2]`

.**Grid spacing**This parameter appears when you set

**Sensor array**to`Replicated subarray`

and**Subarrays layout**to`Rectangular`

.Specify the rectangular grid spacing of subarrays as a real-valued positive scalar, a 1-by-2 row vector, or

`Auto`

. Grid spacing units are expressed in meters.If

**Grid spacing**is a scalar, the spacing along the row and the spacing along the column is the same.If

**Grid spacing**is a 1-by-2 row vector, the vector has the form`[SpacingBetweenRows,SpacingBetweenColumn]`

. The first entry specifies the spacing between rows along a column. The second entry specifies the spacing between columns along a row.If

**Grid spacing**is set to`Auto`

, replication preserves the element spacing of the subarray for both rows and columns while building the full array. This option is available only when you specify**Geometry**as`ULA`

or`URA`

.

**Subarray positions (m)**This parameter appears when you set

**Sensor array**to`Replicated subarray`

and**Subarrays layout**to`Custom`

.Specify the positions of the subarrays in the custom grid as a 3-by-

*N*matrix, where*N*is the number of subarrays in the array. Each column of the matrix represents the position of a single subarray, in meters, in the array’s local coordinate system. The coordinates are expressed in the form`[x; y; z]`

.**Subarray normals**This parameter appears when you set the

**Sensor array**parameter to`Replicated subarray`

and the**Subarrays layout**to`Custom`

.Specify the normal directions of the subarrays in the array. This parameter value is a 2-by-

*N*matrix, where*N*is the number of subarrays in the array. Each column of the matrix specifies the normal direction of the corresponding subarray, in the form`[azimuth; elevation]`

. Each angle is in degrees and is defined in the local coordinate system.You can use the

**Subarray positions**and**Subarray normals**parameters to represent any arrangement in which pairs of subarrays differ by certain transformations. The transformations can combine translation, azimuth rotation, and elevation rotation. However, you cannot use transformations that require rotation about the normal.**Expression**A valid MATLAB expression containing an array constructor, for example,

`phased.URA`

.

**Element type**Specify antenna or microphone type as

`Isotropic Antenna`

`Cosine Antenna`

`Custom Antenna`

`Omni Microphone`

`Custom Microphone`

**Exponent of cosine pattern**This parameter appears when you set

**Element type**to`Cosine Antenna`

.Specify the exponent of the cosine pattern as a scalar or a 1-by-2 vector. You must specify all values as non-negative real numbers. When you set

**Exponent of cosine pattern**to a scalar, both the azimuth direction cosine pattern and the elevation direction cosine pattern are raised to the specified value. When you set**Exponent of cosine pattern**to a 1-by-2 vector, the first element is the exponent for the azimuth direction cosine pattern and the second element is the exponent for the elevation direction cosine pattern.**Operating frequency range (Hz)**This parameter appears when

**Element type**is set to`Isotropic Antenna`

,`Cosine Antenna`

, or`Omni Microphone`

.Specify the operating frequency range, in hertz, of the antenna element as a 1-by-2 row vector in the form

`[LowerBound,UpperBound]`

. The antenna element has no response outside the specified frequency range.**Operating frequency vector (Hz)**This parameter appears when

**Element type**is set to`Custom Antenna`

or`Custom Microphone`

.Specify the frequencies, in Hz, at which to set the antenna and microphone frequency responses as a 1-by-

*L*row vector of increasing values. Use**Frequency responses**to set the frequency responses. The antenna or microphone element has no response outside the frequency range specified by the minimum and maximum elements of**Operating frequency vector (Hz)**.**Frequency responses (dB)**This parameter appears when

**Element type**is set to`Custom Antenna`

or`Custom Microphone`

.Specify this parameter as the frequency response of an antenna or microphone, in decibels, for the frequencies defined by

**Operating frequency vector (Hz)**. Specify**Frequency responses (dB)**as a 1-by-*L*vector matching the dimensions of the vector specified in**Operating frequency vector (Hz)**.**Azimuth angles (deg)**This parameter appears when

**Element type**is set to`Custom Antenna`

.Specify the azimuth angles at which to calculate the antenna radiation pattern as a 1-by-

*P*row vector.*P*must be greater than 2. Angle units are in degrees. Azimuth angles must lie between –180° and 180° and be in strictly increasing order.**Elevation angles (deg)**This parameter appears when the

**Element type**is set to`Custom Antenna`

.Specify the elevation angles at which to compute the radiation pattern as a 1-by-

*Q*vector.*Q*must be greater than 2. Angle units are in degrees. Elevation angles must lie between –90° and 90° and be in strictly increasing order.**Radiation pattern (dB)**This parameter appears when the

**Element type**is set to`Custom Antenna`

.The magnitude in db of the combined polarized antenna radiation pattern specified as a

*Q*-by-*P*matrix or a*Q*-by-*P*-by-*L*array. The value of*Q*must match the value of*Q*specified by**Elevation angles (deg)**. The value of*P*must match the value of*P*specified by**Azimuth angles (deg_**. The value of*L*must match the value of*L*specified by**Operating frequency vector (Hz)**.**Polar pattern frequencies (Hz)**This parameter appears when the

**Element type**is set to`Custom Microphone`

.Specify the measuring frequencies of the polar patterns as a 1-by-

*M*vector. The measuring frequencies lie within the frequency range specified by**Operating frequency vector (Hz)**. Frequency units are in Hz.**Polar pattern angles (deg)**This parameter appears when

**Element type**is set to`Custom Microphone`

.Specify the measuring angles of the polar patterns, as a 1-by-

*N*vector. The angles are measured from the central pickup axis of the microphone, and must be between –180° and 180°, inclusive.**Polar pattern (dB)**This parameter appears when

**Element type**is set to`Custom Microphone`

.Specify the magnitude of the microphone element polar pattern as an

*M*-by-*N*matrix.*M*is the number of measuring frequencies specified in**Polar pattern frequencies (Hz)**.*N*is the number of measuring angles specified in**Polar pattern angles (deg)**. Each row of the matrix represents the magnitude of the polar pattern measured at the corresponding frequency specified in**Polar pattern frequencies (Hz)**and all angles specified in**Polar pattern angles (deg)**. Assume that the pattern is measured in the azimuth plane. In the azimuth plane, the elevation angle is 0° and the central pickup axis is 0° degrees azimuth and 0° degrees elevation. Assume that the polar pattern is symmetric around the central axis. You can construct the microphone’s response pattern in 3-D space from the polar pattern.**Baffle the back of the element**This check box appears only when the

**Element type**parameter is set to`Isotropic Antenna`

or`Omni Microphone`

.Select this check box to baffle the back of the antenna element. In this case, the antenna responses to all azimuth angles beyond ±90° from

*broadside*are set to zero. Define the broadside direction as 0° azimuth angle and 0° elevation angle.

The block input and output ports correspond to the input and
output parameters described in the `step`

method of
the underlying System
object. See link at the bottom of this page.

Port | Description | Supported Data Types |
---|---|---|

`X` |
Arriving signals input port The size of the first dimension of this input matrix can vary to simulate a changing signal length, such as a pulse waveform with variable pulse repetition frequency. | Double-precision floating point |

`Ang` |
Incident directions of signals input port. | Double-precision floating point |

`W` |
Array or subarray weights input port. To enable this port, select
the | Double-precision floating point |

`WS` |
Subarray element weights input port. To enable this port select
| |

`Steer` |
Steering angle input port. To enable this port, select
| Double-precision floating point |

`Out` | Collected signals | Double-precision floating point |

Was this topic helpful?