Hydraulic pipeline with resistive, fluid inertia, and fluid compressibility properties
The Segmented Pipeline block models hydraulic pipelines with circular cross sections. Hydraulic pipelines, which are inherently distributed parameter elements, are represented with sets of identical, connected in series, lumped parameter segments. It is assumed that the larger the number of segments, the closer the lumped parameter model becomes to its distributed parameter counterpart. The equivalent circuit of a pipeline adopted in the block is shown below, along with the segment configuration.
Pipeline Equivalent Circuit
The model contains as many Constant Volume Hydraulic Chamber blocks as there are segments. The chamber lumps fluid volume equal to
|N||Number of segments|
The Constant Volume Hydraulic Chamber block is placed between two branches, each consisting of a Hydraulic Resistive Tube block and a Fluid Inertia block. Every Hydraulic Resistive Tube block lumps (L+L_ad)/(N+1)-th portion of the pipe length, while Fluid Inertia block has L/(N+1) length (L_ad denotes additional pipe length equal to aggregate equivalent length of pipe local resistances, such as fitting, elbows, bends, and so on).
The nodes to which Constant Volume Hydraulic Chamber blocks are connected are assigned names N_1, N_2, …, N_n (n is the number of segments). Pressures at these nodes are assumed to be equal to average pressure of the segment. Intermediate nodes between Hydraulic Resistive Tube and Fluid Inertia blocks are assigned names nn_0, nn_1, nn_2, …, nn_n. The Constant Volume Hydraulic Chamber blocks are named ch_1, ch_2, …, ch_n, Hydraulic Resistive Tube blocks are named tb_0, tb_1, tb_2, …, tb_n, and Fluid Inertia blocks are named fl_in_0, fl_in_1, fl_in_2, …, fl_in_n.
The number of segments is the block parameter. In determining the number of segments needed, you have to find a compromise between the accuracy and computational burden for a particular application. It is practically impossible to determine analytically how many elements are necessary to get the results with a specified accuracy. The golden rule is to use as many elements as possible based on computational considerations, and an experimental assessment is perhaps the only reliable way to make any conclusions. As an approximate estimate, you can use the following formula:
|N||Number of segments|
|c||Speed of sound in the fluid|
|ω||Maximum frequency to be observed in the pipe response|
The table below contains an example of simulation of a pipeline where the first four true eigenfrequencies are 89.1 Hz, 267 Hz, 446 Hz, and 624 Hz.
|Number of Segments||1st Mode||2nd Mode||3rd Mode||4th Mode|
As you can see, the error is less than 5% if an eight-segmented version is used.
The block positive direction is from port A to port B. This means that the flow rate is positive if it flows from A to B, and the pressure loss is determined as .
Internal diameter of the pipe. The default value is 0.01 m.
Pipe geometrical length. The default value is 5 m.
Number of lumped parameter segments in the pipeline model. The default value is 1.
This parameter represents total equivalent length of all local resistances associated with the pipe. You can account for the pressure loss caused by local resistances, such as bends, fittings, armature, inlet/outlet losses, and so on, by adding to the pipe geometrical length an aggregate equivalent length of all the local resistances. This length is added to the geometrical pipe length only for hydraulic resistance computation. Both the fluid volume and fluid inertia are determined based on pipe geometrical length only. The default value is 1 m.
Roughness height on the pipe internal surface. The parameter is typically provided in data sheets or manufacturer's catalogs. The default value is 1.5e-5 m, which corresponds to drawn tubing.
Specifies the Reynolds number at which the laminar flow regime is assumed to start converting into turbulent. Mathematically, this is the maximum Reynolds number at fully developed laminar flow. The default value is 2000.
Specifies the Reynolds number at which the turbulent flow regime is assumed to be fully developed. Mathematically, this is the minimum Reynolds number at turbulent flow. The default value is 4000.
The parameter can have one of two values: Rigid or Compliant. If the parameter is set to Rigid, wall compliance is not taken into account, which can improve computational efficiency. The value Compliant is recommended for hoses and metal pipes where wall compliance can affect the system behavior. The default value is Rigid.
Coefficient that establishes relationship between the pressure and the internal diameter at steady-state conditions. This coefficient can be determined analytically for cylindrical metal pipes or experimentally for hoses. The parameter is used if the Pipe wall type parameter is set to Compliant, and the default value is 2e-10 m/Pa.
Time constant in the transfer function that relates pipe internal diameter to pressure variations. By using this parameter, the simulated elastic or viscoelastic process is approximated with the first-order lag. The value is determined experimentally or provided by the manufacturer. The default value is 0.008 s.
Gas-specific heat ratio for the Constant Volume Hydraulic Chamber block. The default value is 1.4.
Lets you specify the initial condition for pressure inside the pipe segments. The parameter can have one of two values:
The same initial pressure for all nodes — The initial pressure in all pipe segments is the same, and is specified by the Initial pressure parameter value. This is the default.
Custom — Lets you specify initial pressure individually for each pipe segment, by using the Initial pressure vector parameter. The vector size must be equal to the number of pipe segments, defined by the Number of segments parameter value.
Specifies the initial pressure in all pipe segments. The parameter is used if the Initial pressures at model nodes parameter is set to The same initial pressure for all nodes, and the default value is 0.
Lets you specify initial pressure individually for each pipe segment. The parameter is used if the Initial pressures at model nodes parameter is set to Custom. The vector size must be equal to the number of pipe segments, defined by the Number of segments parameter value.
Specifies the initial flow rate through the pipe. The default value is 0.
Parameters determined by the type of working fluid:
Fluid kinematic viscosity
The block has the following ports: