Planetary gear set of carrier, worm planet, and sun wheels with adjustable gear ratio, worm thread type, and friction losses
Simscape / Driveline / Gears / Planetary Subcomponents
The Sun-Planet Worm Gear block represents a two-degree-of-freedom planetary gear built from carrier, sun, and planet gears. By type, the sun and planet gears are crossed helical spur gears arranged as a worm-gear transmission, in which the planet gear is a worm. Such transmissions are used in the Torsen type 1 differential. When transmitting power, the sun gear can be independently rotated by the worm (planet) gear, or by the carrier, or both.
You specify a fixed gear ratio, which is determined as the ratio of the worm angular velocity to the sun gear angular velocity. You control the direction by setting the worm thread type, left-handed or right-handed. Rotation of the right-handed worm in positive direction causes the sun gear to rotate in positive direction too. The positive directions of the sun gear and the carrier are the same.
You can model the effects of heat flow and temperature change through an optional thermal conserving port. By default, the thermal port is hidden. To expose the thermal port, right-click the block in your model and, from the context menu, select Simscape > Block choices. Select a variant that includes a thermal port. Specify the associated thermal parameters for the component.
|RWG||Gear, or transmission, ratio determined as the ratio of the
worm angular velocity to the gear angular velocity.|
The ratio is positive for the right-hand worm and negative for the left-hand worm.
|ωS||Angular velocity of the sun gear|
|ωP||Planet (that is, worm) angular velocity|
|ωC||Carrier angular velocity|
|ωSC||Angular velocity of the sun with respect to the carrier|
|α||Normal pressure angle|
|λ||Worm lead angle|
|d||Worm pitch diameter|
|τS||Torque applied to the sun shaft|
|τP||Torque applied to the planet shaft|
|τC||Torque applied to the carrier shaft|
|τloss||Torque loss due to meshing friction. The loss depends on the
device efficiency and the power flow direction.|
To avoid abrupt change of the friction torque at ωS = 0, the friction torque is introduced via the hyperbolic function.
|τinstfr||Instantaneous value of the friction torque added to the model to simulate friction losses|
|τfr||Steady-state value of the friction torque|
|ηWG||Efficiency for worm-gear power transfer|
|ηGW||Efficiency for gear-worm power transfer|
|μSC||Sun-carrier viscous friction coefficient|
|μWC||Worm-carrier viscous friction coefficient|
Sun-planet worm gear imposes one kinematic constraint on the three connected axes:
ωS = ωP/RWG + ωC .
The gear has two independent degrees of freedom. The gear pair is (1,2) = (S,P).
The torque transfer is:
RWGτP + τS – τloss = 0 ,
τC = – τS,
with τloss = 0 in the ideal case.
For general considerations on nonideal gear modeling, see Model Gears with Losses.
In a nonideal gear, the angular velocity and geometric constraints are unchanged. But the transferred torque and power are reduced by:
Coulomb friction between thread surfaces on W and G, characterized by friction coefficient k or constant efficiencies [ηWG, ηGW]
Viscous coupling of driveshafts with bearings, parametrized by viscous friction coefficients μSC and μWC
Because the transmission incorporates a worm gear, the efficiencies are different for the direct and reverse power transfer. The following table shows the value of the efficiency for all combinations of the power transfer.
|Driving shaft||Driven shaft|
In the contact friction case, ηWG and ηGW are determined by:
The worm-gear threading geometry, specified by lead angle λ and normal pressure angle α.
The surface contact friction coefficient k.
ηWG = (cosα – k·tanλ)/(cosα + k/tanλ) ,
ηGW = (cosα – k/tanλ)/(cosα + k·tanα) .
In the constant efficiency case, you specify ηWG and ηGW, independently of geometric details.
If you set efficiency for the reverse power flow to a negative value, the train exhibits self-locking. Power can not be transmitted from sun gear to worm and from carrier to worm unless some torque is applied to the worm to release the train. In this case, the absolute value of the efficiency specifies the ratio at which the train is released. The smaller the train lead angle, the smaller the reverse efficiency.
The efficiencies η of meshing between worm and gear are fully active only if the transmitted power is greater than the power threshold.
If the power is less than the threshold, the actual efficiency is automatically regularized to unity at zero velocity.
The viscous friction coefficients of the worm-carrier and sun-carrier bearings control the viscous friction torque experienced by the carrier from lubricated, nonideal gear threads. For details, see Nonideal Gear Constraints.
Gear inertia is assumed negligible.
Gears are treated as rigid components.
Coulomb friction slows down simulation. See Adjust Model Fidelity.
|C||Rotational conserving port representing the gear carrier|
|W||Rotational conserving port representing the worm gear|
|S||Rotational conserving port representing the sun gear|
|H||Thermal conserving port for thermal modeling|
Gear or transmission ratio
RWG determined as the
ratio of the worm angular velocity to the gear angular velocity. The
Choose the directional sense of gear rotation corresponding to
positive worm rotation. The default is
If you select
Left-handed, rotation of the worm in
the generally-assigned positive direction results in the gear rotation
in negative direction.
Parameters for meshing and friction losses vary with the block variant chosen—one with a thermal port for thermal modeling and one without it.
Vector of viscous friction coefficients
μSC], for the worm-carrier and
sun-carrier shafts, respectively. The default is
From the drop-down list, choose units. The default is
Thermal energy required to change the component temperature
by a single degree. The greater the thermal mass, the more resistant
the component is to temperature change. The default value is
Component temperature at the start of simulation. The initial
temperature alters the component efficiency according to an efficiency
vector that you specify, affecting the starting meshing or friction
losses. The default value is
For optimal simulation performance, use the Friction Losses > Friction model parameter default setting,
No friction losses - Suitable
for HIL simulation.