Note: This page has been translated by MathWorks. Please click here

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

To view all translated materals including this page, select Japan from the country navigator on the bottom of this page.

Output periodic piecewise linear signal

Physical Signals/Sources

The Repeating Sequence block outputs a periodic
piecewise linear signal, * y*. You can optionally
specify an initial signal value and an initial time offset. The repeating
sequence consists of a number of linear segments, connected to each
other. The number of segments must be no greater than 100. You specify
how to connect the segments by choosing a signal type. For the same
set of block parameter values, the resulting output signal will be
different depending on the signal type:

`Discontinuous`

— Each linear segment in the repeating sequence is defined by its duration, start value, and end value. If the end value of a segment is not the same as the start value of the next segment, they are connected by a vertical line.`Continuous`

— Each linear segment in the repeating sequence is defined by its duration and start value. The end value of a segment is the same as the start value of the next segment.`Discrete`

— Each linear segment in the repeating sequence is defined by its duration and start value. The end value of a segment is the same as its start value.

Use this block to generate various types of physical signals, such as pulse, sawtooth, stair, and so on.

**Initial output**The value of the output signal at time zero. The output of the block remains at this value until the simulation time reaches the

**Time offset**value. The default value is`0`

.**Time offset**The value of the initial time offset, before the start of the repeating sequence. During this time, the output of the block remains at the

**Initial output**value. The default value is`0`

.**Signal type**Select one of the following signal types:

`Discontinuous`

— For each linear segment in the repeating sequence, define its duration, start value, and end value. If the end value of a segment is not the same as the start value of the next segment, they are connected by a vertical line. This is the default method.`Continuous`

— For each linear segment in the repeating sequence, define its duration and start value. The end value of a segment is the same as the start value of the next segment.`Discrete`

— For each linear segment in the repeating sequence, define its duration and start value. The end value of a segment is the same as its start value.

**Durations**Specify the linear segment durations as a 1–by–

row vector, where`n`

is the number of linear segments in the repeating sequence.`n`

must be no greater than 100. The default is`n`

`[ 1 1 ]`

s, which means two linear segments, each lasting 1 second.**Start output values**Specify the start values of the output signal for each linear segment as a 1–by–

row vector, where`n`

is the number of linear segments in the repeating sequence. The size of the vector must match the size of the`n`

**Durations**row vector. The default is`[ 0 2 ]`

, which means that the first of the two linear segments starts at 0, and the second one starts at 2.**End output values**Specify the end values of the output signal for each linear segment as a 1–by–

row vector, where`n`

is the number of linear segments in the repeating sequence. The size of the vector must match the size of the`n`

**Durations**row vector. The default is`[ 1 1 ]`

. This parameter is only visible if the**Signal type**parameter is set to`Discontinuous`

. For other signal types, the end value of a segment is defined either by the start value of the next segment (`Continuous`

) or the start value of the same segment (`Discrete`

).

The block has one physical signal output port.

This example shows the mapping between the block parameter values and the resulting output signal.

Set the block parameters as shown:

The following plot shows the resulting block output.

The signal starts at 0 and consists of two linear segments. The duration of the first segment is 1 second, the segment starts at 0 and ends at 4. The signal is discontinuous, and the end value of the first segment is different than the start value of the second segment, therefore they are connected by a vertical line. The second segment starts at 2, lasts for 2 seconds, and ends at 0, after which the sequence repeats.

Was this topic helpful?