Interface between two-phase fluid and mechanical rotational networks
The Rotational Mechanical Converter (2P) block models an interface between two-phase fluid and mechanical rotational networks. The interface converts pressure in the fluid network into torque in the mechanical rotational network and vice versa.
This block enables you to model a rotary actuator powered by a two-phase fluid system. It does not, however, account for inertia, friction, or hard stops, common in rotary actuators. You can model these effects separately using Simscape blocks such as Inertia, Rotational Friction, and Rotational Hard Stop.
Port A represents the inlet through which fluid enters and exits the converter. Ports C and R represent the converter casing and moving interface, respectively. Port H represents the wall through which the converter exchanges heat with its surroundings.
The torque direction depends on the mechanical orientation of the converter. If the Mechanical Orientation parameter is positive, then a positive flow rate through the inlet tends to rotate the moving interface in the positive direction relative to the converter casing.
Positive Mechanical Orientation
If the Mechanical Orientation parameter is negative, then a positive mass flow rate through the inlet tends to rotate the moving interface in the negative direction relative to the converter casing.
Negative Mechanical Orientation
The flow resistance between port A and the converter interior is assumed negligible. Pressure losses between the two is approximately zero. The pressure at port A is therefore equal to that in the converter:
pA is the pressure at port A.
pI is the pressure in the converter.
Similarly, the thermal resistance between port H and the converter interior is assumed negligible. The temperature gradient between the two is approximately zero. The temperature at port H is therefore equal to that in the converter:
TH is the temperature at port H.
TI is the temperature in the converter.
The volume of fluid in the converter is the sum of the dead and displaced fluid volumes. The dead volume is the amount of fluid left in the converter at a zero interface angle. This volume enables you to model the effects of dynamic compressibility and thermal capacity even when the interface is in its zero position.
The displacement volume is the amount of fluid added to the converter due to rotation of the moving interface. This volume increases with the interface angle. The total volume in the converter as a function of the interface angle is
V is the total volume of fluid in the converter.
Vdead is the dead volume of the converter.
Dvol is the displaced fluid volume per unit rotation of the interface.
θint is the rotation angle of the moving interface.
∊or is an integer encoding the mechanical orientation of the converter:
At equilibrium, the internal pressure in the converter counteracts the external pressure of its surroundings and the torque exerted by the mechanical network on the moving interface. This torque is the reverse of that applied by the fluid network. The torque balance in the converter is therefore
patm is the environmental pressure outside the converter.
tint is the magnitude of the torque exerted by the fluid network on the moving interface.
The total energy in the converter can change due to energy flow through the inlet, heat flow through the converter wall, and work done on the mechanical network. The energy flow rate, given by the energy conservation equation, is therefore
E is the total energy of the fluid in the converter.
ϕA is the energy flow rate into the converter through port A.
ϕH is the heat flow rate into the converter through port H.
Taking the fluid kinetic energy in the converter to be negligible, the total energy of the fluid reduces to:
M is the fluid mass in the converter.
uI is the specific internal energy of the fluid in the converter.
The fluid mass in the converter can change due to flow through the inlet, represented by port A. The mass flow rate, given by the mass conservation equation, is therefore
is the mass flow rate into the converter through port A.
A change in fluid mass can accompany a change in fluid volume, due to rotation of the moving interface. It can also accompany a change in mass density, due to an evolving pressure or specific internal energy in the converter. The mass rate of change in the converter is then
is the partial derivative of density with respect to pressure at constant specific internal energy.
is the partial derivative of density with respect to specific internal energy at constant pressure.
vI is the specific volume of the fluid in the converter.
The block blends the density partial derivatives of the various domains using a cubic polynomial function. At a vapor quality of 0–0.1, this function blends the derivatives of the subcooled liquid and two-phase mixture domains. At a vapor quality of 0.9–1, it blends those of the two-phase mixture and superheated vapor domains.
The smoothed density partial derivatives introduce into the original mass conservation equation undesirable numerical errors. To correct for these errors, the block adds the correction term
∊M is the correction term.
τ is the phase-change time constant—the characteristic duration of a phase change event. This constant ensures that phase changes do not occur instantaneously, effectively introducing a time lag whenever they occur.
The final form of the mass conservation equation is
The converter walls are rigid. They do not deform under pressure.
The flow resistance between port A and the converter interior is negligible. The pressure is the same at port A and in the converter interior.
The thermal resistance between port H and the converter interior is negligible. The temperature is the same at port H and in the converter interior.
The moving interface is perfectly sealed. No fluid leaks across the interface.
Mechanical effects such as hard stops, inertia, and friction, are ignored.
Orientation of the moving interface relative to the two-phase
fluid network. If the orientation is positive, then a positive flow
into the converter results in a positive rotation of port R relative
to port C. If the orientation is negative, then a positive flow into
the converter results in a negative rotation of port R relative to
port C. The default setting is
Displaced fluid volume per unit rotation of the moving interface.
The default value is
Angle of the moving interface at the start of simulation. A
zero angle corresponds to a total fluid volume in the converter equal
to the specified dead volume. The default value is
This parameter must be greater than or equal to zero if the Mechanical
orientation parameter is set to
It must be smaller than or equal to zero if the Mechanical
orientation parameter is set to
Volume of fluid left in the converter when the interface angle
is zero. The dead volume enables the block to account for mass and
energy storage in the converter even at a zero interface angle. The
default value is
Flow area of the converter inlet, represented by port A.
Pressure losses due to changes in flow area inside the converter are
ignored. The default value is
Pressure characteristics of the surrounding environment. Select
pressure to set the environment pressure to the atmospheric
pressure specified in the Two-Phase Fluid
Properties (2P) block. Select
Specified pressure to
set the environment pressure to a different value. The default setting
Absolute pressure of the surrounding environment. The environment
pressure acts against the internal pressure of the converter and affects
the motion of the converter shaft. This parameter is active only when
the Environment pressure specification parameter
is set to
Specified pressure. The default
0.101325 MPa, corresponds to atmospheric
pressure at mean sea level.
Fluid regime at the start of simulation. The fluid can be a
subcooled liquid, a two-phase mixture, or a superheated vapor. The
default setting is
Pressure in the converter at the start of simulation. The default
Temperature in the converter at the start of simulation. This
parameter appears only when the Initial fluid regime parameter
is set to
Subcooled liquid or
vapor. The default value is
Characteristic duration of a phase-change event. This constant
introduces a time lag into the transition between phases. The default
The block has the following ports:
Two-phase fluid conserving port associated with the converter inlet.
Thermal conserving port representing the converter surface through which heat exchange occurs.
Mechanical rotational conserving port associated with the converter rotor.
Mechanical rotational conserving port associated with the converter case.