Compute steady-state values of voltages and currents of model
sps = power_steadystate('sys')
power_steadystate('sys') opens the Steady-State
Voltages and Currents Tool dialog box that allows you to view steady-state
values of the inductor currents and capacitor voltages (electrical
state variables), steady-state voltages and currents of measurement
blocks and sources, as well as steady-state voltages and currents
of nonlinear blocks of a model. This tool can also be activated from
the Powergui block dialog box by selecting Steady-State
Voltages and Currents.
If the model contains power electronic switches (diodes, thyristors, IGBTs, and so on) the steady-state values are computed considering them as open-circuit. If the model contains breakers (Breaker, Three-Phase Breaker, Three-Phase Fault blocks) the steady-state values are computed considering their initial status (open-circuit or short-circuit).
sps = power_steadystate('sys') returns
a structure with the fields:
|The name of the model|
|Vector listing the source frequencies in the model|
|The names of the electrical states of the model|
|The steady-state values of electrical states of the model|
|The names of the dependent states, if any|
|The names of the Measurement blocks of the model|
|The steady-state values of measurement blocks of the model|
|The names of the electrical source blocks of the model|
|The steady-state values of the electrical sources of the model|
|The names of the outputs corresponding to the nonlinear blocks (current-source injection based models). It consist of the measured terminal voltages used by the nonlinear models to compute the corresponding current sources|
|The steady-state values of outputs used by the nonlinear blocks|
|The names of the inputs corresponding to the nonlinear blocks of the model|
|The steady-state values of current inputs defined by the nonlinear blocks (current-source injection based models)|
When the model contains more that one source frequency, the
Display measurements of steady-state voltages and currents in the model.
Set the Units parameter to
values to display the peak values of the selected values.
Set the Units parameter to
RMS to display the root-mean-square (RMS) values
of the selected values.
Allows you to choose the frequency, in hertz (Hz), that you want for display of the voltage and current phasors. The Frequency parameter lists all the different frequencies of the electrical sources of the model.
If selected, the window displays the steady-state phasors of the capacitor voltages and inductor currents of the circuit. The default is unselected.
If selected, the window displays the steady-state voltage and current phasors of the measurement blocks of the circuit. The default is selected.
If selected, the window displays the steady-state voltage and current phasors of the electrical sources of the circuit. The default is unselected.
If selected, the window displays the steady-state voltages and currents of the nonlinear blocks of the circuit. The default is unselected.
In the pull-down menu, choose the format in which you want your
measurements displayed. The
floating point option
is displayed in mantissa-exponent form with five significant figures.
best of option displays with four significant
figures and uses mantissa-exponent form only for numbers larger than
9999. The final option is displayed in plain numbers with two figures
to the right of the decimal point. The default is
In the pull-down menu, choose the ordering in which you want
your measurements displayed. The V
alue then name option
displays the steady-state values in the first column followed by the
names of the states variables. The
Name then value option
displays the name of the states variables in the first column followed
by the steady-state values.
Recompute and display the steady-state measurements.
Unlike Simulink® signal lines and input and output ports, the Physical Modeling connection lines and terminal ports lack intrinsic directionality. The voltage and current polarities are determined, not by line direction, but instead by block orientation. To find out a block orientation, first click on the block to select it. Then enter the following command:
The following table indicates the polarities of the currents and voltages for single-phase and three-phase RLC elements (branches or loads), surge arresters, and single-phase and three-phase breakers. The table also indicates the polarities of their state variables (inductor currents and capacitor voltages).
left —> right
Vleft – Vright
right —> left
Vright – Vleft
top —> bottom
Vtop – Vbottom
bottom —> top
Vbottom – Vtop
The natural orientation of the blocks (that is, their orientation in the Element library) is right for horizontal blocks and down for vertical blocks.
For single-phase transformers (linear or saturable), with the winding connectors appearing on the left and right sides, the winding voltages are the voltages of the top connector with respect to the bottom connector whatever the block orientation (right or left). The winding currents are the currents entering the top connector. For three-phase transformers, the voltage polarities and positive current directions are indicated by the signal labels used in the Multimeter block.