Change Simulink 3D Animation preferences
Name of the preference.
New value of the preference.
This function sets the given Simulink® 3D Animation™ preference
to a given value. The following preferences are defined. For preferences
that begin with the string
these values are the default values for the corresponding
Creates a thumbnail of a virtual world when you open
a virtual world. The default is
Specifies the handling of the virtual world
Specifies handling of the virtual world
Specifies the handling of the virtual world
Controls the appearance of the control panel in the
Specifies default units for new
Determines whether antialiasing is used by default for
Specifies default file name for capturing viewer figures.
Specifies the default callback invoked when closing a
Specifies whether the lights are rendered by default
Specifies the default maximum size of a texture used
in rendering new
Specifies the default appearance of the control panel
in the viewer. Valid values are
Specifies whether the navigation zone is on or off by
default for new
Sets the default initial position and size of the Simulink 3D Animation Viewer window. Valid value is a vector of four doubles.
Specifies the default compression method for creating
2-D animation files for new
Specifies the default quality of 2-D animation file compression
Specifies the default 2-D offline animation file name
Specifies the default frames per second playback speed.
have the 2D AVI animation play back at approximately the same playback
speed as the 3D virtual world animation, set this preference to
Specifies whether to render a
Specifies whether the status bar appears by default at
the bottom of the Simulink 3D Animation Viewer for new
Specifies whether textures should be rendered by default
Specifies whether the toolbar appears by default on the Simulink 3D Animation Viewer
Specifies whether or not transparency information is
taken into account when rendering for new
Specifies whether objects are drawn as solids or wireframes
by default for new
Specifies which viewer is used to view a virtual scene.
Specifies the default 3-D animation file name for new
Specifies the default animation recording mode for new
Specifies the default start and stop times for scheduled
animation recording for new
Specifies whether the virtual world is enabled by default
for remote viewing for new
Specifies the default source of the time for new
Specifies which virtual world editor to use. Path to the virtual world editor. If this path is empty, the MATLAB® editor is used.
The path setting is active only if you select
To open a virtual
world file in a third-party editor, do not use the
Specifies whether the 3D World Editor starts up with
a saved version of the layout of a virtual world when you exited it
or reverts to the default layout. The layout of the virtual world
display pane includes settings for the view, viewpoints, navigation,
and rendering. Valid values are
IP port number used to access the Simulink 3D Animation server over the Web via HTTP. If you change this preference, you must restart the MATLAB software before the change takes effect.
Length of the transport buffer (network packet overlay) for communication between the Simulink 3D Animation server and its clients.
Amount of time the Simulink 3D Animation server waits for a reply from the client. If there is no response from the client, the Simulink 3D Animation server disconnects from the client.
IP port used for communication between the Simulink 3D Animation server and its clients. If you change this preference, you must restart the MATLAB software before the change takes effect.
When you use
'factory' as a single argument,
all preferences are reset to their default values. If you use
a preference value, that single preference is reset to its default.
TransportBuffer preferences affect Web-based
viewing of virtual worlds.
the Simulink 3D Animation Viewer. Changes to the
take effect only after you restart the MATLAB software.
DefaultFigureNavPanel — Controls the
appearance of the navigation panel in the Simulink 3D Animation Viewer.
For example, setting this value to
the navigation panel to appear translucent.
DefaultViewer — Determines whether
the virtual scene appears in the default Simulink 3D Animation Viewer
or in your Web browser.
Default Simulink 3D Animation Viewer.
Viewer is the default Web browser with the virtual world plug-in.
Editor — Contains a path to the virtual
world editor executable file. When you use the
edit command, Simulink 3D Animation runs
the virtual world editor executable with all parameters required to
edit the virtual world file.
When you run the editor, Simulink 3D Animation uses the
value as if you typed it into a command line. The following tokens
Refers to the MATLAB root folder
Refers to the virtual world 3D file name
For instance, a possible value for the
If this preference is empty, the MATLAB editor is used.
HttpPort -- Specifies the network port to
be used for remote Web access. The port is given in the Web URL as
The default value of this preference is
TransportBuffer — Defines the size
of the message window for client-server communication. This value
determines how many messages, at a maximum, can travel between the
client and the server at one time.
Generally, higher values for this preference make the animation run more smoothly, but with longer reaction times. (More messages in the line create a buffer that compensates for the unbalanced delays of the network transfer.)
The default value is
5, which is optimal
for most purposes. You should change this value only if the animation
is significantly distorted or the reaction times are very slow. On
fast connections, where delays are introduced more by the client rendering
speed, this value has very little effect. Viewing on a host computer
is equivalent to an extremely fast connection. On slow connections,
the correct value can improve the rendering speed significantly but,
of course, the absolute maximum is determined by the maximum connection
VrPort — Specifies the network port
to use for communication between the Simulink 3D Animation server
(host computer) and its clients (client computers). Normally, this
communication is completely invisible to the user. However, if you
view a virtual world from a client computer, you might need to configure
the security network system (firewall) so that it allows connections
on this port. The default value of this preference is