This example shows how to use Simulink® Design Verifier™ functions to replace unsupported blocks and to how customize test vector generation for specific requirements.

The example model includes a Switch block whose output is controlled by a Sqrt block. For each switch position, the output of the model is calculated by a 1-D Lookup Table block. For this model, the example concentrates on generating test cases that satisfy the following:

1. Achieve 100% lookup table coverage.

2. Test vectors demonstrate each Switch block position when the values of its first and third input ports differ.

```
open_system('sldvdemo_sqrt_blockrep');
```

Since the `sqrt`

function is not supported, this model is partially compatible with Simulink Design Verifier.

```
sldvcompat('sldvdemo_sqrt_blockrep');
```

Entering Stage: 'SLDV Compatibility Analysis' for Model: 'sldvdemo_sqrt_blockrep' Checking compatibility of model 'sldvdemo_sqrt_blockrep' Compiling model... done Checking compatibility... done Warning: Simulink Design Verifier has only partial support for some elements of the model: 'sldvdemo_sqrt_blockrep' is partially compatible with Simulink Design Verifier. The model can be analyzed by Simulink Design Verifier. It contains unsupported elements that will be stubbed out during analysis. The results of the analysis might be incomplete. Warning: Block 'sldvdemo_sqrt_blockrep/Sqrt' is configured to operate as function sqrt. Simulink Design Verifier does not support this function. 'sldvdemo_sqrt_blockrep' is partially compatible with Simulink Design Verifier. The model can be analyzed by Simulink Design Verifier. It contains unsupported elements that will be stubbed out during analysis. The results of the analysis might be incomplete. Exiting Stage: 'SLDV Compatibility Analysis' for Model: 'sldvdemo_sqrt_blockrep'

This model can be analyzed for test generation by automatically stubbing the unsupported Sqrt block. However, test cases cannot be generated for the Switch block positions because Simulink Design Verifier does not understand the Sqrt block and the output of this block is effecting the Switch block. Since you want test cases for the Switch block, you need to replace the Sqrt block with a supported block that is functionally equivalent. The library block `sldvdemo_custom_blockreplib`

shown below constrains the input signal to the range `[0 10000]`

and approximates the `sqrt`

function by using a 1-D Lookup Table block.

The table data was calculated to match the values of `sqrt`

, with a maximum error of `0.2`

in the range `[0 10000]`

. Refer to the mask initialization pane of the block `Sqrt_Approx`

in the library `sldvdemo_custom_blockreplib`

for the values of the lookup table data.

The replacement rule is in defined the MATLAB-file `sldvdemo_custom_blkrep_rule_sqrt.m`

. Since the replacement block `sldvdemo_custom_blockreplib`

for the Sqrt block is only valid for double or single types, this rule ensures that these conditions are satisfied before allowing a block replacement.

function rule = sldvdemo_custom_blkrep_rule_sqrt

rule = SldvBlockReplacement.blockreprule; rule.fileName = mfilename;

rule.blockType = 'Sqrt';

rule.replacementPath = sprintf('sldvdemo_custom_blockreplib/Sqrt_Approx');

rule.replacementMode = 'Normal';

parameter.OutMin = '$original.OutMin$'; parameter.OutMax = '$original.OutMax$'; parameter.OutDataTypeStr = '$original.OutDataTypeStr$'; rule.parameterMap = parameter;

rule.isReplaceableCallBack = @replacementTestFunction;

end

function out = replacementTestFunction(blockH)

out = false; acceptedOutDataTypeStr = {'double','single',... 'Inherit: Inherit via back propagation',... 'Inherit: Same as input'}; I = strmatch(get_param(blockH,'OutDataTypeStr'),acceptedOutDataTypeStr,'exact'); if ~isempty(I)

portDataTypes = get_param(blockH,'CompiledPortDataTypes');

out = any(strcmp(portDataTypes.Inport,{'double','single'})) && ... strcmp(portDataTypes.Inport,portDataTypes.Outport); end end

open_system('sldvdemo_custom_blockreplib'); open_system('sldvdemo_custom_blockreplib/Sqrt_Approx/1-D Lookup Table');

You will run Simulink Design Verifier in test generation mode with block replacements enabled. In order to generate test cases for positions of Switch block, you must use the custom replacement rule `sldvdemo_custom_blkrep_rule_sqrt.m`

.

Since you are also interested in lookup table coverage, you need the built-in block replacement `blkrep_rule_lookup_normal.m`

, which inserts test objectives for each interval and breakpoint value for a 1-D Lookup Table block. Moreover, you need the built-in rule `blkrep_rule_switch_normal.m`

, which requires that each switch position be exercised when the values of the first and third input ports differ. Please refer to the Block Replacement in the Simulink Design Verifier documentation for a list of all built-in replacement rules.

The analysis will run for a maximum of 30 seconds and produce a harness model. Report generation is also enabled. Other Simulink Design Verifier options are set to their default values.

opts = sldvoptions; opts.Mode = 'TestGeneration'; opts.MaxProcessTime = 30; opts.BlockReplacement = 'on'; opts.BlockReplacementRulesList = ['sldvdemo_custom_blkrep_rule_sqrt.m,' ... 'blkrep_rule_lookup_normal.m,'... 'blkrep_rule_switch_normal.m']; opts.SaveHarnessModel = 'on'; opts.ModelReferenceHarness = 'on'; opts.SaveReport = 'on';

The `sldvrun`

function analyzes the model using the settings defined in a `sldvoptions`

object `opts`

. The generated report includes a chapter summarizing block replacements performed on the model.

```
[status,fileNames] = sldvrun('sldvdemo_sqrt_blockrep', opts, true);
```

Enable the lookup table coverage metric and then run the test cases using the harness model. You can also execute the suite of tests by clicking the "Run all" button on the Signal Builder dialog box after enabling lookup table coverage from the "Analysis" > "Coverage" > "Settings" menu.

The coverage report shown below indicates that you can reach 100% lookup table coverage with the test vectors that Simulink Design Verifier generated.

[harnessModelPath,harnessModel] = fileparts(fileNames.HarnessModel); set_param(harnessModel,'covMetricSettings','dcmte'); sldvdemo_playall(harnessModel);

To complete the example, close all models and remove the files that Simulink Design Verifier generated.

close_system('sldvdemo_custom_blockreplib'); close_system(fileNames.HarnessModel,0); close_system(fileNames.BlockReplacementModel,0); close_system('sldvdemo_sqrt_blockrep',0); delete(fileNames.HarnessModel); delete(fileNames.BlockReplacementModel); delete(fileNames.DataFile);

Was this topic helpful?