Documentation

Vehicle Network Toolbox Properties

Alphabetical List By Category

CAN Communication

Hardware Connection

BusLoad Display load on CAN bus
Database Store CAN database information
MessageReceivedFcn Specify function to run
MessageReceivedFcnCount Specify number of messages available before function is triggered
OnboardTermination Configure bus termination on device
Running Determine status of channel
SilentMode Specify if channel is active or silent
StartTriggerTerminal Specify start trigger source terminal
TransceiverName Name of device transceiver
TransceiverState Display state or mode of transceiver
UserData Enter custom data
Device Display channel device type
Device(NI) Display NI CAN channel device type
DeviceChannelIndex Display device channel index
DeviceSerialNumber Display device serial number
DeviceVendor Display device vendor name
InitializationAccess Determine control of device channel
BusSpeed Indicate bit rate of bus
NumOfSamples Display number of samples available to channel
SJW Synchronization jump width (SJW) of bit time segment
TSEG1 Display amount that channel can lengthen sample time
TSEG2 Display amount that channel can shorten sample time

Transmit Messages

Data CAN message or J1939 parameter group data
Database Store CAN database information
Error CAN message error frame
Extended Identifier type for CAN message
ID Identifier for CAN message
Name CAN message name
Remote Specify CAN message remote frame
Signals Display physical signals defined in CAN message or J1939 parameter group
UserData Enter custom data

Receive Messages

MessageReceivedFcn Specify function to run
MessageReceivedFcnCount Specify number of messages available before function is triggered
MessagesAvailable Display number of messages available to be received by CAN channel
MessagesReceived Display number of messages received by CAN channel
MessagesTransmitted Display number of messages transmitted by CAN channel
InitialTimestamp Indicate when channel started
Timestamp Display message received timestamp
ReceiveErrorCount Display number of received errors detected by channel
TransmitErrorCount Display number of transmitted errors by channel

Message Database

Messages Store message names from CAN database
Name CAN database name
Path Display CAN database folder path
UserData Enter custom data

XCP Communication

Message Database

Events Display A2L events list
Measurements Display A2L measurements list
DAQInfo Data acquisition information in A2L file
SlaveName Name of connected slave
FileName Name of referenced A2L file
FilePath Path of A2L file
ProtocolLayerInfo Protocol layer information
TransportLayerCANInfo CAN transport layer information

Hardware Connection

A2LFileName Name of the A2L file
SeedKeyDLL Name of seed and key security access dll
SlaveName Name of connected slave
TransportLayer Transport layer type
TransportLayerDevice XCP transport layer connection

Acquire and Stimulate Measurements

A2LFileName Name of the A2L file
SeedKeyDLL Name of seed and key security access dll
SlaveName Name of connected slave
TransportLayer Transport layer type
TransportLayerDevice XCP transport layer connection

J1939 Communication

Parameter Group

Priority Priority of parameter group
SourceAddress Address of parameter group source
DestinationAddress Address of parameter group destination
Data CAN message or J1939 parameter group data
Signals Display physical signals defined in CAN message or J1939 parameter group
UserData Enter custom data
Name J1939 parameter group name
PGN J1939 parameter group number
PDUFormatType J1939 parameter group PDU format
Timestamp Display parameter received timestamp

Channels

TransceiverState Display state or mode of transceiver
SilentMode Specify if channel is active or silent
UserData Enter custom data
DeviceVendor Display device vendor name
Device Display channel device type
DeviceChannelIndex Display device channel index
DeviceSerialNumber Display device serial number
ParameterGroupsAvailable Number of parameter groups available
ParameterGroupsReceived Number of parameter groups received
ParameterGroupsTransmitted Number of parameter groups transmitted
FilterPassList List of parameter groups to pass
FilterBlockList List of parameter groups to block
Running Determine status of channel
BusStatus Determine status of bus
InitializationAccess Determine control of device channel
SilentMode Specify if channel is active or silent
TransceiverName Name of device transceiver
TransceiverState Display state or mode of transceiver
BusSpeed Indicate bit rate of bus
SJW Synchronization jump width (SJW) of bit time segment
TSEG1 Display amount that channel can lengthen sample time
TSEG2 Display amount that channel can shorten sample time
NumOfSamples Display number of samples available to channel
Was this topic helpful?