This example shows how to trace a signal using a software triggered Simulink® Real-Time™ host scope. After the script builds and downloads the oscillator model, xpcosc, to the target computer, it adds a scope of type 'host' to the real-time application and the signals 'Integrator1' and 'Signal Generator' to the scope. The scope is then configured in the software trigger mode.
Once the trigger is initiated, the scope is monitored to determine when its data acquisition is complete. Next, the scope data is uploaded to the development computer and plotted. This process repeats 25 times. The software trigger is re-enabled each run after a random pause (between 0 and 4 seconds). After every fifth run, the damping gain 'Gain1/Gain' is set to a new random value (between 0 and 2000).
Use 'slrtpingtarget' to test the connection between the development and target computers.
if ~strcmp(slrtpingtarget, 'success') error(message('xPCTarget:examples:Connection')); end
Open the oscillator model, xpcosc. Under the model's configuration parameter Simulink Real-Time option settings, the system target file has been set to slrt.tlc. Hence, building the model will create an executable image, xpcosc.mldatx, that can be run on a PC booted with the Simulink Real-Time kernel.
Build the model and download the image, xpcosc.mldatx, to the target computer.
set_param('xpcosc','RTWVerbose','off'); % Configure for a non-Verbose build. rtwbuild('xpcosc'); % Build and download application.
### Starting Simulink Real-Time build procedure for model: xpcosc ### Generated code for 'xpcosc' is up to date because no structural, parameter or code replacement library changes were found. ### Successful completion of build procedure for model: xpcosc ### Looking for target: TargetPC1 ### Download model onto target: TargetPC1
Create the MATLAB® variable, tg, containing the Simulink Real-Time target object. This object allows you to communicate with and control the target computer.
tg = slrt; % Create a Simulink Real-Time target object tg.SampleTime = 0.000250; % Set sample time to 250us tg.StopTime = 10000; % Set stop time to a high value (10000s) start(tg); % Start model execution
Create, configure, and plot to the host scope during each run.
tPar = getparamid(tg, 'Gain1', 'Gain'); % Get index of parameter 'Gain1/Gain' signals(1) = getsignalid(tg, 'Integrator1'); % Get index of signal 'Integrator1' signals(2) = getsignalid(tg, 'Signal Generator'); % Get index of signal 'Signal Generator' sc = addscope(tg, 'host'); % Define (add) a host scope object addsignal(sc, signals); % Add signals to signal list of scope object sc.NumSamples = 200; % Set number of samples sc.Decimation = 4; % Set decimation factor sc.TriggerMode ='Software'; % Set trigger mode figh = findobj('Name', 'scsoftwaredemo');% Does the plot figure exist? if isempty(figh) figh = figure; % No: Create figure set(figh, 'Name', 'scsoftwaredemo', 'NumberTitle', 'off'); else figure(figh); % Yes: Make it the current figure end % Loop to acquire 25 data packages from the scope object. m = 1; flag = 0; for n = 1 : 25 if isempty(find(get(0, 'Children') == figh, 1)), flag = 1; break; end % Change parameter Gain1/Gain every fifth acquisition loop % to a random value between 0 and 2000. if ~m setparam(tg, tPar, 2*1000*rand); end m = rem(m + 1, 5); start(sc); % Start scope object % Wait until scope object has 'ready' state. while ~strcmp(sc.Status, 'Ready for being Triggered'), end % Randomize the amount of wait time before triggering scope. % Wait a random period (0..4s). ttrigger = rand * 4; title(['scsoftwaredemo: ', num2str(n), ... ' of 25 data packages, will be triggered in ', ... num2str(ttrigger), 's']); pause(ttrigger); if isempty(find(get(0, 'Children') == figh, 1)), flag = 1; break; end % Software trigger the scope object. trigger(sc); % Wait until scope-object has 'finished' state. while ~strcmpi(sc.Status,'finished'); end % Create time vector, upload scope data and display it. t = sc.Time; % Upload time vector plot(t, sc.Data); % Upload acquired data and plot set(gca, 'XLim', [t(1), t(end)], 'YLim', [-10, 10]); drawnow; end if ~flag, title('scsoftwaredemo: finished'); end
When done, stop the application and close the model.
stop(tg); % Stop model close_system('xpcosc',0); % Close model