No BSD License  

Highlights from
SD Toolbox

SD Toolbox

by

 

Set of Simulink models for the simulation of sigma-delta modulators.

BP2IP3.m
% ************************************************************************
% 2nd Order Sigma-Delta BandPass A/D Modulator
% by S. Brigati & F. Francesconi Ver.(0.1) 24/09/99
% The modulator structure is simulated using Simulink (bp2IP.mdl).
% Post-processing of the results is done with Matlab.
% 1. Plots the Power Spectral Density of the bit-stream
% 2. Calculates the IP3
% 3. Calculates histograms at the integrator outputs
% ************************************************************************
clear

t0=clock;

% ************************************************************************
% Variabili globali
% ************************************************************************
bw=200e3;					% Base-band
R=107;						% 42.8 MHz sampling rate
% R=50;					% 20.0 MHz sampling rate
Fs=R*2*bw;				% Oversampling frequency
Ts=1/Fs;
N=65536;					% Samples number
nper=32;
Fin1=(Fs/4)+ nper*Fs/N;	% Input signal frequency 
Fin2=(Fs/4)- nper*Fs/N;	% Input signal frequency 

Ampl=0.5-pi/256;			% Input signal amplitude [V]
Ntransient=0
%
% kT/C noise and op-amp non-idealities
%
echo on;
k=1.38e-23;			% Boltzmann Constant
Temp=300;				% Absolute Temperature in Kelvin
Cf=4e-12;				% Integrating Capacitance of the first integrator
alfa=(711-1)/711;	% A=Op-amp finite gain (alfa=(A-1)/A -> ideal op-amp alfa=1)
% alfa=1;
Amax=2;				% Op-amp saturation value [V]
sr=280e6;				% Op-amp slew rate [V/s]
GBW=250e6;			% Op-amp GBW [Hz]
noise1=4.39e-3;		% 1st int. output noise std. dev. [V/sqrt(Hz)]
% noise1=0;
delta=0.1e-9;			% Random Sampling jitter (std. dev.) [s] (Boser, Wooley JSSC Dec. 88)
% delta=0;
echo off;
%
% Modulator coefficients
%
echo on;
b=0.125;		% 1/8 gain of the first stage
b2=0.125;		% 1/8 gain of the second stage
b3=0.25		% 1/4 additional gain of the second feedback loop
Vref=1;
echo off;

finrad1=Fin1*2*pi;		% Input signal frequency in radians
finrad2=Fin2*2*pi;		% Input signal frequency in radians


s0=sprintf('** Simulation Parameters **');
s1=sprintf('   Fs(Hz)=%1.0f',Fs);
s2=sprintf('   Ts(s)=%1.6e',Ts);
s3=sprintf('   Fin1(Hz)=%1.4f',Fin1);
s4=sprintf('   Fin2(Hz)=%1.4f',Fin2);
s5=sprintf('   BW(Hz)=%1.0f',bw);
s6=sprintf('   OSR=%1.0f',R);
s7=sprintf('   Npoints=%1.0f',N);
s8=sprintf('   tsim(sec)=%1.3f',N/Fs);
s9=sprintf('   Nperiods=%1.3f',N*Fin1/Fs);
disp(s0)
disp(s1)
disp(s2)
disp(s3)
disp(s4)
disp(s5)
disp(s6)
disp(s7)
disp(s8)
disp(s9)
% ************************************************************************
% Open Simulink diagram first
% ************************************************************************

options=simset('InitialState', zeros(1,4), 'RelTol', 1e-3, 'MaxStep', 1/Fs);
sim('bp2IP', (N+Ntransient)/Fs, options);	% Starts Simulink simulation

% ************************************************************************
%   Calculates PSD and IP3 of the bit-stream and of the signal
% ************************************************************************
w=hann(N);
echo on;
f=Fin1/Fs						% Normalized signal frequency
fB=N*(bw/Fs)					% Base-band frequency bins
fBL=N*(1/4-bw/(2*Fs))		% Lower limit Base-band frequency bins
fBH=N*(1/4+bw/(2*Fs))		% Higher limit Base-band frequency bins


yy1=zeros(1,N);
yy1=yout(2+Ntransient:1+N+Ntransient)';

echo off;

ptot=zeros(1,N);
[snr,ptot]=calcSNRBP(yy1(1:N),f,fBL,fBH,w,N,Vref);


% Calculate intermodulation products
fip1=N*Fin1/Fs;
fip2=N*Fin2/Fs;
fip31=2*fip1-fip2;
fip32=2*fip2-fip1;

ampdb1=ptot(ceil(fip1));
ampdb2=ptot(ceil(fip31));
ampdb3=ptot(ceil(fip2));
ampdb4=ptot(ceil(fip32));

IP3=min(abs(ampdb2-ampdb1), abs(ampdb4-ampdb3));

% ************************************************************************
% Graphical output
% ************************************************************************

figure(1);
clf;
plot(linspace(0,Fs/2,N/2), ptot(1:N/2), 'r');
grid on;
title('PSD of a 2nd-Order Band-Pass Sigma-Delta Modulator')
xlabel('Frequency [Hz]')
ylabel('PSD [dB]')
axis([0 Fs/2 -100 0]);


figure(2);
clf;
plot(linspace(0,Fs/2,N/2), ptot(1:N/2), 'r');
hold on;
title('PSD of a 2nd-Order Band-Pass Sigma-Delta Modulator (detail)')
xlabel('Frequency [Hz]')
ylabel('PSD [dB]')
axis([(Fs/4 - bw/2) (Fs/4 + bw/2) -100 0]);
grid on;
hold off;
text_handle = text(floor(Fs/4),-40, sprintf('IP3 = %4.1fdB',IP3));
text_handle = text(floor(Fin1),ampdb1+10, sprintf('ampdb1 = %4.1fdB',ampdb1));
text_handle = text(floor(fip31*Fs/N),ampdb2+10, sprintf('ampdb2 = %4.1fdB',ampdb2));
text_handle = text(floor(Fin2),ampdb3+15, sprintf('ampdb3 = %4.1fdB',ampdb3));
text_handle = text(floor(fip32*Fs/N),ampdb4+10, sprintf('ampdb4 = %4.1fdB',ampdb4));

s1=sprintf('   IP3(dB)=%1.3f',IP3);
s2=sprintf('   Simulation time =%1.3f min',etime(clock,t0)/60);
disp(s1)
disp(s2)

% ************************************************************************
% Histograms of the integrator outputs
% ************************************************************************

figure(4)
nbins=200;
[bin1,xx1]=histo(y1, nbins);
[bin2,xx2]=histo(y2, nbins);
clf;
subplot(1,2,1), plot(xx1, bin1)
grid on;
title('First Integrator Output')
xlabel('Voltage [V]')
ylabel('Occurrences')
subplot(1,2,2), plot(xx2, bin2)
grid on;
title('Second Integrator Output')
xlabel('Voltage [V]')
ylabel('Occurrences')

Contact us