Code covered by the BSD License  

Highlights from
RF Design and Analysis

• C2F (C) C2F Convert a temperature from Centigrade to Farenheit
• C2K (C) C2K Convert a temperature from Centigrade to Kelvin
• F2C (F) F2C Convert a temperature from Farenheit to Centigrade
• F2K (F) F2K Convert a temperature from Farenheit to Kelvin
• FFTSNDR(samples, fsample, fsi... FFTSNDR Function to find SNR from an FFT
• GaussFilt(BW, N) GAUSSFILT Design a Gaussian Low-Pass Filter
• GaussSQNR(L, MQL, STD); GAUSSSQNR Function to calculate SQNR of A/D converter with Gaussian input
• IMR(a, p) IMR Calculate image rejection ratio given amplitude and phase mismatch
• K2C (K) K2C Convert a temperature from Kelvin to Centigrade
• K2F (K) K2F Convert a temperature from Kelvin to Farenheit
• MUSTRIPLOSS (EpsR, EpsE, tand... MUSTRIPLOSS Calculate the attenuation of a microstrip line
• MUSTRIPZ0 (EpsR, WbyD) MUSTRIPZ0 Calculate the characteristic impedance of a microstrip line
• PulseSource (X, RT, FT, W, T,... PULSESOURCE Generates output of pulsed source
• SIMPLE_GM(mode, IN, W, L, Mu0... SIMPLE_GM Function to find transconductance given drain current or overdrive voltage
• SINEAPPROX(T, F, A, C) SINEAPPROX Generates a clipped sine wave and an approximation to it.
• STRIPLINELOSS (EpsR, tandelta... STRIPLINELOSS Calculate the attenuation of a stripline
• STRIPLINEZ0 (EpsR, WbyB) STRIPLINEZ0 Calculate the characteristic impedance of a stripline
• adbP (x) ADBP Convert a decibel signal into a power signal
• adbV (x) ADBV Convert a decibel signal into an amplitude signal
• adbm (x) ADBM Convert a dbm signal into a power signal (Watts)
• binomialtransformer (Zl, Z0, ... BINOMIALTRANSFORMER Design a multisection binomial impedance transformer
• binomialxfrmrbw (Zl, Z0, N, G... BINOMIALXFRMRBW Calculate the bandwidth of a binomial transformer
• ccc2pcc (ccc); CCC2PCC Converts a complex number into magnitude and phase (in radians)
• cfreqz.m CFREQZ Function to plot pole-zero plot and transfer function of complex poles
• chebpoly(N,X) CHEBPOLY Evaluate Chebyshev polynomial
• compare(varargin); COMPARE Function to plot two vectors of different scales on same x axis
• dbP (x) DBP Convert a power signal into decibels
• dbV (x) DBV Convert a voltage signal into decibels
• dbm (x) DBM Convert a power signal (Watts) into dbm
• deg2rad (deg) DEG2RAD Convert a vector from degrees to radians
• digital(varargin); DIGITAL Function to plot digital signals
• fft_a_p_mismatch(samples1, sa... FFT_A_P_MISMATCH Amplitude and phase mismatch of two signals from an FFT
• fftamp(samples, fs, f0, varar... FFTPHASE Function to find phase of a particular frequency from an FFT
• fftamp(samples, fs, f0, varar... FFTAMP Function to find amplitude of a particular frequency from an FFT
• fftbandamp(samples, fs, fL, f... FFTBANDAMP Function to find rms amplitude of a particular band from an FFT
• freqs1 (B,A,W) FREQS1 Function to find the frequency response of a filter at 1 frequency
• iscmplx (x) ISCMPLX Tests if a number or array is complex
• iseven (x) ISEVEN Tests if a number or vector is even
• isodd (x) ISODD Tests if a number or vector is odd
• lambertw (A)
• llimit (x, m); LLIMIT Limit a vector to a given minimum value
• loadspice(infname) LOADSPICE Reads in SPICE data from .out file
• logfft(samples, fs, vpp, vara... LOGFFT Function to plot FFT
• mask (vect, maskv) MASK Mask a vector using another vector. Include only those elements in the
• mustrip (H, Z0, EpsR) MUSTRIP Calculate the required width of a microstrip line
• mustripw (Weff, T, H) MUSTRIPW Calculate the width of a microstrip line from the effective width required
• mustripweff (W, T, H) MUSTRIPWEFF Calculate the effective width of a microstrip line
• parallel (varargin) PARALLEL Computes the value of components in "parallel"
• pcc2ccc (mag, ang); PCC2CCC Convert the polar input into a complex number
• pinkfilt (alpha, numtaps) PINKFILT Generate filter coefficients for a 'pink noise' filter.
• rad2deg (rad) RAD2DEG Convert a vector from radians to degrees
• repeat(x, N); REPEAT Upsample a vector by inserting repeated samples
• rflib RFLIB Open the RF Circuits Toolbox SIMULINK Block Library.
• rms (x) RMS Compute the RMS value of a vector
• roundto (X, Resolution) ROUNDTO Round the input to a specified resolution
• sd_fft(samples, fs, vpp, vara... PLOTFFT Function to plot FFT
• sigres(x,y) SIGRES Function to plot the signal response of a complex system
• singlestub (Z0, Zl, STUBTYPE)... SINGLESTUB Computes the single-stub matching networks for a given Zl and Z0
• singlestubresponse (Z0, Zl, D... SINGLESTUBRESPONSE Computes the frequency response of a single-stub match
• stripline (H, Z0, EpsR) STRIPLINE Calculate the required width of a stripline
• ulimit (x, m); ULIMIT Limit a vector to a given maximum value
• uniquepcnt(a, PCNT) UNIQUEPCNT Set unique, ignoring roundoff error.
• vectfilt (vect, type) VECTFILT Filter a vector to have only specific type of elements. Types are 'real',
• IMR_JT.m
• L1PSD.m
• constants.m
• RF
• View all files