MATLAB Answers


Best way to acess external config data (load mat file vs import data vs fscanf etc. )

Asked by Mathieu
on 13 Jun 2014
Latest activity Answered by Pritesh Shah on 17 Jun 2014

Greetings, I need to store some external parameters in a configuration file (not more than 50 lines). It is not yet defined how many subfunction will need to have access to it but the overall speed will be important. The whole application will be compiled in the end.

I found multiple ways to do this but I am not sure what is the best way: I could load a mat file, read an ascii txt file, a csv and so on (and all this with multiple possibilities).

What is the best (most efficient) way to do this ?



A stream file is what is often called "binary" -- fread/fwrite

I think the structure of a configuration object is the far cleaner solution--it encapsulates the changes inside the structure and is, therefore, far less prone to rampant changes in code at least isolating the interfaces.

Again, unless you insist on embedding this i/o operation deeply within a nested loop or somesuch, it's almost certainly to be of no never-mind in performance overall; it's just unwise to not do as good a job of factorization and encapsulation as feasible at the git-go rather than start with a bad factoring from the beginning.

If there are subsections that need disparate data, create specific structures or the like for them to minimize the amount of data being passed around rather than reload stuff randomly.

I'd say likely (but only timing with a specific file size/structure can prove it) the order would be


The higher-level functions trailing in no known order but stuff like importdata that are generic and do a lot of testing to handle anything automagically will likely bring up the rear and possibly by a fairly wide margin.

Thanks a lot!

I also intuitively thought importdata would be slow, but for some weird reason associated it with the speed of "load" that you implied. It makes complete sense this way.

I use fread/fwrite with virtual com ports but have no idea how to use that with local files. Anyhow, I don't think it is worth to investigate now.

I'll start with a load and will switch to fscanf if needed.

Thanks again for the support.

The biggest difference in speed between the classes is whether they're formatted or unformatted files. The overhead for formatted files is first there's many more bytes/numeric value and secondly it takes compute-time to do the conversion from/to internal storage to the ASCII representation.

For formatted files the higher-level, more convenient forms TMW supplies have all the extra processing and logic built into them that make them more convenient to use but that also comes at a price of far more complexity in the processing. load is slightly more complex than a pure stream of bytes owing to the fact it also saves the structure and the information associated with the variable(s) whereas all of that is your responsibility if you simply write an array as the byte stream.

Similarly, if use fscanf by itself, all the formatting and structure in the file is written explicitly so there's no additional internal logic. If you use one of the more convenient forms then they eventually get down to the final call to the i/o but they have (a varying amount of) flexibility built in so again, that costs something in performance in payback for the convenience (there is no free lunch).

OTOH, for the size of the data you're talking about, I'll reemphasize that write the code for ease of maintainability and clarity of expression first; the amount of data you're talking about is so minimal as to be of no concern for execution time or storage space (again, presuming the avoidance of doing the same thing over and over and over...).

Log in to comment.

2 Answers

Answer by Mathieu
on 17 Jun 2014
 Accepted Answer

The following comment pretty much answers my question:


Log in to comment.

Answer by Pritesh Shah on 17 Jun 2014

I think, You may try tic and toc command to find out optimal solution for your case.


Log in to comment.

Discover MakerZone

MATLAB and Simulink resources for Arduino, LEGO, and Raspberry Pi

Learn more

Discover what MATLAB® can do for your career.

Opportunities for recent engineering grads.

Apply Today

MATLAB Academy

New to MATLAB?

Learn MATLAB today!