Clear Filters
Clear Filters

Perform cross co-relation to find best fit

3 views (last 30 days)
Hello Community,
I have two signals s_acti.mat and phs1.mat.
how do i find the time interval of s_acti that best fits with phs1.
i intend to perform cross corelation and find the suitable time frame in s_acti that best fits with phs1.

Answers (1)

Mathieu NOE
Mathieu NOE on 13 Dec 2021
hello
the two signals have a slightly (but constant) slopes , so the best estimation of time delta is measured at half the amplitude
>> dt = - t0_neg1 + t0_neg2
dt = 1.1076e-08
code :
clc
clearvars
load('s_acti.mat');
time1 = s_acti(:,1);
data1 = s_acti(:,2);
load('phs1.mat');
time2 = phs1(:,1);
data2 = phs1(:,2);
%% my code below
threshold = min(data1)/2; % your value here
[t0_pos1,s0_pos1,t0_neg1,s0_neg1]= crossing_V7(data1,time1,threshold,'linear'); % positive (pos) and negative (neg) slope crossing points
% ind => time index (samples)
% t0 => corresponding time (x) values
% s0 => corresponding function (y) values , obviously they must be equal to "threshold"
[t0_pos2,s0_pos2,t0_neg2,s0_neg2]= crossing_V7(data2,time2,threshold,'linear'); % positive (pos) and negative (neg) slope crossing points
figure(4)
plot(time1,data1,time2,data2,time1,threshold*ones(size(time1)),'k--',t0_neg1,s0_neg1,'dr',t0_neg2,s0_neg2,'dg','linewidth',2,'markersize',12);grid on
legend('signal 1','signal 2','threshold','negative slope crossing points signal 1','negative slope crossing points signal 2');
dt = - t0_neg1 + t0_neg2
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
function [t0_pos,s0_pos,t0_neg,s0_neg] = crossing_V7(S,t,level,imeth)
% [ind,t0,s0,t0close,s0close] = crossing_V6(S,t,level,imeth,slope_sign) % older format
% CROSSING find the crossings of a given level of a signal
% ind = CROSSING(S) returns an index vector ind, the signal
% S crosses zero at ind or at between ind and ind+1
% [ind,t0] = CROSSING(S,t) additionally returns a time
% vector t0 of the zero crossings of the signal S. The crossing
% times are linearly interpolated between the given times t
% [ind,t0] = CROSSING(S,t,level) returns the crossings of the
% given level instead of the zero crossings
% ind = CROSSING(S,[],level) as above but without time interpolation
% [ind,t0] = CROSSING(S,t,level,par) allows additional parameters
% par = {'none'|'linear'}.
% With interpolation turned off (par = 'none') this function always
% returns the value left of the zero (the data point thats nearest
% to the zero AND smaller than the zero crossing).
%
% check the number of input arguments
error(nargchk(1,4,nargin));
% check the time vector input for consistency
if nargin < 2 | isempty(t)
% if no time vector is given, use the index vector as time
t = 1:length(S);
elseif length(t) ~= length(S)
% if S and t are not of the same length, throw an error
error('t and S must be of identical length!');
end
% check the level input
if nargin < 3
% set standard value 0, if level is not given
level = 0;
end
% check interpolation method input
if nargin < 4
imeth = 'linear';
end
% make row vectors
t = t(:)';
S = S(:)';
% always search for zeros. So if we want the crossing of
% any other threshold value "level", we subtract it from
% the values and search for zeros.
S = S - level;
% first look for exact zeros
ind0 = find( S == 0 );
% then look for zero crossings between data points
S1 = S(1:end-1) .* S(2:end);
ind1 = find( S1 < 0 );
% bring exact zeros and "in-between" zeros together
ind = sort([ind0 ind1]);
% and pick the associated time values
t0 = t(ind);
s0 = S(ind);
if ~isempty(ind)
if strcmp(imeth,'linear')
% linear interpolation of crossing
for ii=1:length(t0)
%if abs(S(ind(ii))) >= eps(S(ind(ii))) % MATLAB V7 et +
if abs(S(ind(ii))) >= eps*abs(S(ind(ii))) % MATLAB V6 et - EPS * ABS(X)
% interpolate only when data point is not already zero
NUM = (t(ind(ii)+1) - t(ind(ii)));
DEN = (S(ind(ii)+1) - S(ind(ii)));
slope = NUM / DEN;
slope_sign(ii) = sign(slope);
t0(ii) = t0(ii) - S(ind(ii)) * slope;
s0(ii) = level;
end
end
end
% extract the positive slope crossing points
ind_pos = find(sign(slope_sign)>0);
t0_pos = t0(ind_pos);
s0_pos = s0(ind_pos);
% extract the negative slope crossing points
ind_neg = find(sign(slope_sign)<0);
t0_neg = t0(ind_neg);
s0_neg = s0(ind_neg);
else
% empty output
ind_pos = [];
t0_pos = [];
s0_pos = [];
% extract the negative slope crossing points
ind_neg = [];
t0_neg = [];
s0_neg = [];
end
end
  6 Comments
Mathieu NOE
Mathieu NOE on 14 Mar 2022
hello Sajid
good news and happy that you could find a solution to your problem
all the best
M

Sign in to comment.

Products


Release

R2020b

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!