1 view (last 30 days)

Show older comments

I am struggling to understand how to setup some indexing problem in MATLAB. If my entire domain is defined from 1 to N with a padding of two cells. So say my internal domain (domain without padded cells) from 2 to N-2, then if I want to calculate some values at the "interfaces" of the cells instead at the cells, how can I setup this on MATLAB? For example I have the following code for the internal domain that I would like to change my indicies to the interfaces?

My set up is like:

% calculate Flux at j+1/2

%

% j+1/2 Cell's grid:

% | wL| |

% | /|wR | 1 2 3 4 N-2 N-1 N

% | / |\ | {x=0} |-o-|-o-|-o-|-o-| ... |-o-|-o-|-o-| {x=L}

% |/ | \ | 1 2 3 4 5 N-1 N N+1

% | | \|

% | | | NC: Here cells 1 and N are ghost cells%

% j j+1

I keep getting the error:

Index in position 2 exceeds array bounds

The code for example:

function [ U_L, U_R] = MUSCL(U,N,NEQ )

size_U = size(U);

U_L = zeros(size_U);

U_R = zeros(size_U);

delta = 1e-6; % epsilon

for i= 1:NEQ

for j = 3:N-1

denom_L = (U(i,j) - U(i,j-1));

denom_R = (U(i,j+2) - U(i,j+1)); % error here since index exceeds the bounds of the array N (1001 here)

denom_L = sign(denom_L+1e-64)*max(delta, abs(denom_L));

denom_R = sign(denom_R+1e-64)*max(delta, abs(denom_R));

r_L = (U(i,j) - U(i,j-1))/denom_L;

r_R = (U(i,j+2) - U(i,j+1))/denom_R;

theta_L = Limiter(r_L);

theta_R = Limiter(r_R);

end

end

for j = 2:N-2

U_L(:,j) = U(:,j)+0.5*theta_R.*(U(:,j)-U(:, j-1));

U_R(:,j) = U(:,j+1)-0.5*theta_L.*(U(:,j+2)-U(:,j+1));

end

end

How can I find U_L, U_R, r_L, r_R at j+1/2 ??

per isakson
on 8 May 2021

Edited: per isakson
on 8 May 2021

Index in position 2 exceeds array bounds

U(:,j+2) is most likely the problem.

I assume that the size of U is NEQxN. The maximum value of j is N-1 (for j = 3:N-1). Thus, the maximum value of j+2 is N+1, which exceeds the array bound, N

per isakson
on 9 May 2021

Your code is about "flux", "cells" and "interfaces". The name, MUSCL, does that stand for "muscle"? However, I neither understand the physics nor the code. Futhermore, I cannot run the code, since I neither have the function, Limiter(), nor a realistic sample of U.

It looks strange to me that none of the left-hand-side variables in the double loop is indexed.

%% A sample matrix

M = 40 .* membrane( 1, 25 );

%%

to_the_interfaces = @(row) interp1( (1:numel(row)), row, (1.5:1:numel(row)-0.5) );

row = (1:10);

to_the_interfaces(row)

%%

M_at_the_interfaces = nan(size(M)-[0,1]);

for jj = 1 : size(M,1)

M_at_the_interfaces(jj,:) = to_the_interfaces(M(jj,:));

end

imagesc( M_at_the_interfaces )

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!