Community Profile

photo

Antonin


MathWorks

82 total contributions since 2012

Contact

Antonin's Badges

  • Knowledgeable Level 3
  • 6 Month Streak
  • Revival Level 3
  • First Answer
  • Solver

View details...

Contributions in
View by

Answered
Problem in Data Type Conversion - ti C2000 DC/DC Buck Converter example
Hi Saeed Heshmatian, Welcome to the world of Fixed-Point! In many of our examples, we like to keep our units between -1 and 1 ...

1 day ago | 2

| accepted

Answered
Problem in programming 28379D from Simulink
I would start by removing the 14 exclamation marks in the folder name. It looks like the flashing tool doesn't like these.

2 months ago | 0

Answered
eCAN loading problems to TI C2000 C28x3x card; are example only for Vector hardware
Hi Mike, Our CAN solution is based on the Vector XL Library which is compatible with pretty much all Vector hardware. We teste...

2 months ago | 0

Answered
eCAN loading problems to TI C2000 C28x3x card; are example only for Vector hardware
Hi Mike, Our built-in External Mode support over CAN for TI C2000 processors only supports the Vector tools. The Vehicle Netwo...

2 months ago | 0

| accepted

Answered
ADC synchronization with PWM on F2812
Hi Zhe, Unfortunately this is not available on the TI F2812 family of chips. TI added this functionality on newer processors l...

2 months ago | 0

Answered
Integration of code composer code in Simulink Model
Hi Pasquale, In your S-function, use the below construct anywhere needed: #ifndef MATLAB_MEX_FILE /* Place here pro...

2 months ago | 0

| accepted

Answered
How can I create sinus wave by using TI C2000 launchpad and simulink?
Hello Batuhan, # Open a blank Simulink model, go the configuration parameters (Ctrl+E) > Hardware Implementation > Select the...

3 months ago | 0

Answered
is it unable to interface c2000 piccolo F280049C launchxl with Matlab 2017a?
Dear Insta, Support for f28004x started in MATLAB release R2017b as stated in the <https://www.mathworks.com/help/supportpkg/...

4 months ago | 0

Answered
What is the idea behind data processing for SCI communication in DC/DC Buck Converter Example?
Hi Karol, Here is what is happening in the Serial Send subsystem: * The goal is to send data to the host at a fast rate an...

4 months ago | 1

| accepted

Answered
processor in the loop communication between simulink and arduino mega 2560
Dear Mohammed, Have you tried following this example: <https://www.mathworks.com/help/supportpkg/arduino/examples/code-verifi...

5 months ago | 0

Answered
Flash.out.file generated by simulink
On the snapshot below taken from MATLAB R2018a, the "Build action" can automate the load and run part, the "Boot From Flash" ena...

5 months ago | 0

| accepted

Answered
c28379Dpmsmfocdual_cpu1_ert ....I got this link from matlab example code.It is about field oriental control of pmsm motors using delfino 28379d microcontroller.When i paste this link in my command window the model does not open.
It sounds like you haven't installed the <https://www.mathworks.com/matlabcentral/fileexchange/43096-embedded-coder-support-pack...

5 months ago | 0

Answered
GPxPUD register values in C2000 F28035 c28x_LedBlink_ert Simulink Example
Hi Alex, We don't initialize the pull-up registers and the default values after reset are not uniform across the different re...

5 months ago | 0

Submitted


Motor Control with TI LaunchPad
Permanent Magnet Synchronous Motor Field-Oriented Control with TI LaunchPad and BOOSTXL-DRV8301

6 months ago | 58 downloads |

Thumbnail

Submitted


Dual Motor Control with TI LAUNCHXL-F28069M LaunchPad
Field-Oriented Control with TI LAUNCHXL-F28069M, BOOSTXL-DRV8301 inverters and 2 PMS motors

6 months ago | 28 downloads |

Thumbnail

Answered
Where i can get USB drivers for TMS320F28379D dsp kit.?
Hi Nimisha, Drivers are provided with your CCS installation under \ccs_base\emulation\drivers. (on my machine C:\ti\ccsv7\ccs...

7 months ago | 0

Answered
Usage of C2000 TI family launch pad F28069M without Embedded coder
Hi Fernando, The <https://www.mathworks.com/matlabcentral/fileexchange/43096-embedded-coder-support-package-for-texas-instrum...

7 months ago | 0

Answered
How to measure task execution time on F28379D target?
Bonjour Yanis, R2016b was the first release to support the F28379D device. We added quite a few features later on. I would st...

7 months ago | 0

| accepted

Answered
Did someone already use DMC PARK for Park transformation with C2000 concerto ?
Bonjour Antoine, I recommend the following example which uses most DMC blocks. <https://www.mathworks.com/help/supportpkg/...

7 months ago | 0

Answered
F28069M Simulink Failed to Open COM
Hi Euan, Your board may be using a different COM port. This page will help you figure out your COM port: <http://processors...

8 months ago | 1

| accepted

Answered
Unable to read data from the MPU6050 with TI C2000 f28379d & Simulink
Attached is a model that has been created in MATLAB R2016b for the MPU-9150 present on the BOOSTXL-SENSHUB attached to an F28027...

8 months ago | 0

Answered
Problem flashing TI LAUNCHXL-F28379D
Hi Duc Tien Nguyen, I believe your D:\ drive must be a Removable disk (like an SD Card or a USB thumb drive). These use the e...

9 months ago | 1

| accepted

Answered
Unable to read data from the MPU6050 with TI C2000 f28379d & Simulink
Hi Tommaso, The I2C blocks expect a slave I2C address in decimal format. You have to use hex2dec('68') or 104 for the slave a...

9 months ago | 0

Answered
How to open C2000 support package example ?
Hi Loc LE, The example you are pointing to is shipping in MATLAB R2018a. In R2017b you can use <https://www.mathworks.com/he...

9 months ago | 0

Answered
is it possible to inline C2000 (F28379D) legacy code for CLA usage
Hi Alexander, You are close. By default GPIOs are controlled by the CPU and the CLA doesn't have access the registers. As of ...

9 months ago | 0

Answered
Generating PIL from S-Function Unresolved symbol during linking
Hi Michael, The linker doesn't know where to find the init_code() function that you are using in you S-function. You need to...

9 months ago | 0

Answered
Change Parameters on stand alone application without the need of downloading the Simulink model on the Target
Hi Kyriakos, You can run External mode from a power-cycle boot. On your Simulink model, click on the "Code" menu option, then...

9 months ago | 0

| accepted

Answered
is it possible to inline C2000 (F28379D) legacy code for CLA usage
Hi Alexander, Use an S-function with TLC code. You can inline the logic of your C function in the TLC file. In <https://www.m...

10 months ago | 0

Answered
With 28335 TI, embedded coder, for a sine signal with and without presence of ADC block frequency is changing
I agree with Venkatesh, you are most likely overrunning the base rate. Using the ADC in software mode triggers the ADC conversio...

10 months ago | 0

Answered
the third party installation package got skipped while installing Add ons.
Hi Sarvar, The recommend version (6.4.6) refers to the compiler version and not the CCS version. You can get different versi...

11 months ago | 0

Load more