Air-Fuel Ratio Control System with Stateflow Charts

Generate code for an air-fuel ratio control system designed with Simulink® and Stateflow®.

Figures 1, 2, and 3 show relevant portions of the sldemo_fuelsys model, a closed-loop system containing a plant and controller. The plant validates the controller in simulation early in the design cycle. In this example, you generate code for the relevant controller subsystem, "fuel_rate_control". Figure 1 shows the top-level simulation model.

Open sldemo_fuelsys via rtwdemo_fuelsys and compile the diagram to see the signal data types.


Figure 1: Top-level model of the plant and controller

The air-fuel ratio control system is comprised of Simulink® and Stateflow®. The control system is the portion of the model for which you generate code.


Figure 2: The air-fuel ratio controller subsystem

The control logic is a Stateflow® chart that specifies the different modes of operation.


Figure 3: Air-fuel rate controller logic

Close these windows.


Configure and Build the Model with Simulink® Coder™

Simulink® Coder™ generates generic ANSI® C code for Simulink® and Stateflow® models via the Generic Real-Time (GRT) target. You can configure a model for code generation programmatically.


For this example, build only the air-fuel ratio control system. Once the code generation process is complete, an HTML report detailing the generated code is displayed. The main body of the code is located in fuel_rate_control.c.

### Starting build procedure for model: fuel_rate_control
### Successful completion of build procedure for model: fuel_rate_control

Configure and Build the Model with Embedded Coder®

Embedded Coder® generates production ANSI® C/C++ code via the Embedded Real-Time (ERT) target. You can configure a model for code generation programmatically.


Repeat the build process and inspect the generated code. In the Simulink® Coder™ Report, you can navigate to the relevant code segments interactively by using the Previous and Next buttons. From the chart context menu (right-click the Stateflow® block), select Code Generation > Navigate to Code. Programmatically, use the rtwtrace utility.

### Starting build procedure for model: fuel_rate_control
### Successful completion of build procedure for model: fuel_rate_control

View the air-fuel ratio control logic in the generated code.

    '/* Function for Chart:','case IN_Warmup:',1,0);
/* Function for Chart: '<S1>/control_logic' */
static void Fueling_Mode(const int32_T *sfEvent)
  /* This state interprets the other states in the chart to directly control the fueling mode. */
  switch (rtDW.bitsForTID0.is_Fueling_Mode) {
   case IN_Fuel_Disabled:
    rtDW.fuel_mode = DISABLED;

    /* The fuel is completely shut off while in this state. */
    switch (rtDW.bitsForTID0.is_Fuel_Disabled) {
     case IN_Overspeed:
      /* Inport: '<Root>/sensors' */
      /* The speed is dangerously high, so shut off the fuel. */
      if ((rtDW.bitsForTID0.is_Speed == IN_normal) && (rtU.sensors.speed <
           603.0F)) {
        if (rtDW.bitsForTID0.is_Fail != IN_Multi) {
          rtDW.bitsForTID0.is_Fuel_Disabled = IN_NO_ACTIVE_CHILD;
          rtDW.bitsForTID0.is_Fueling_Mode = IN_Running;
          switch (rtDW.bitsForTID0.was_Running) {
           case IN_Low_Emissions:
            rtDW.bitsForTID0.is_Running = IN_Low_Emissions;
            rtDW.bitsForTID0.was_Running = IN_Low_Emissions;
            rtDW.fuel_mode = LOW;
            switch (rtDW.bitsForTID0.was_Low_Emissions) {
             case IN_Normal:
              rtDW.bitsForTID0.is_Low_Emissions = IN_Normal;
              rtDW.bitsForTID0.was_Low_Emissions = IN_Normal;

Close the model and code generation report.

clear hDemo;

Related Examples

For related fixed-point examples that use sldemo_fuelsys, see