Note: This page has been translated by MathWorks. Click here to see

To view all translated materials including this page, select Country from the country navigator on the bottom of this page.

To view all translated materials including this page, select Country from the country navigator on the bottom of this page.

In digital hardware, numbers are stored in binary words. A binary word is a fixed-length sequence of binary digits (1's and 0's). The way in which hardware components or software functions interpret this sequence of 1's and 0's is described by a data type. There are several distinct differences between fixed-point data types and the built-in integer types in MATLAB®. The most notable difference, is that the built-in integer data types can only represent whole numbers, while the fixed-point data types also contain information on the position of the binary point, or the scaling of the number.

Binary numbers are represented as either fixed-point or floating-point data types. A fixed-point data type is characterized by the word size in bits, the binary point, and whether it is signed or unsigned. The position of the binary point is the means by which fixed-point values are scaled and interpreted. With Fixed-Point Designer™, fixed-point data types can be integers, fractionals, or generalized fixed-point numbers. The main difference between these data types is their default binary point. For example, a binary representation of a generalized fixed-point number (either signed or unsigned) is shown below:

where

*b*_{i}is the*i*^{th}binary digit.*wl*is the word length in bits.*b*_{wl-1}is the location of the most significant, or highest, bit (MSB).*b*_{0}is the location of the least significant, or lowest, bit (LSB).The binary point is shown four places to the left of the LSB. In this example, therefore, the number is said to have four fractional bits, or a fraction length of four.

The binary point is the means by which fixed-point numbers are
scaled. It is usually the software that determines the binary point.
When performing basic math functions such as addition or subtraction,
the hardware uses the same logic circuits regardless of the value
of the scale factor. In essence, the logic circuits have no knowledge
of a scale factor. They are performing signed or unsigned fixed-point
binary algebra as if the binary point is to the right of *b*_{0}.

Fixed-Point
Designer supports the general binary point scaling *V*=*Q**2^*E*. `V`

is
the real-world value, `Q`

is the stored integer value,
and `E`

is equal to `-FractionLength`

.
In other words, `RealWorldValue = StoredInteger * 2 ^ -FractionLength`

.

`FractionLength`

defines the scaling of the
stored integer value. The word length limits the values that the stored
integer can take, but it does not limit the values `FractionLength`

can
take. The software does not restrict the value of exponent `E`

based
on the word length of the stored integer `Q`

. Because `E`

is
equal to `-FractionLength`

, restricting the binary
point to being contiguous with the fraction is unnecessary; the fraction
length can be negative or greater than the word length.

For example, a word consisting of three unsigned bits is usually represented in scientific notation in one of the following ways.

$$\begin{array}{l}bbb.=bbb.\times {2}^{0}\\ bb.b=bbb.\times {2}^{-1}\\ b.bb=bbb.\times {2}^{-2}\\ .bbb=bbb.\times {2}^{-3}\end{array}$$

If the exponent were greater than 0 or less than -3, then the representation would involve lots of zeros.

$$\begin{array}{c}bbb00000.=bbb.\times {2}^{5}\\ bbb00.=bbb.\times {2}^{2}\\ .00bbb=bbb.\times {2}^{-5}\\ .00000bbb=bbb.\times {2}^{-8}\end{array}$$

These extra zeros never change to ones, however, so they don't show up in the hardware. Furthermore, unlike floating-point exponents, a fixed-point exponent never shows up in the hardware, so fixed-point exponents are not limited by a finite number of bits.

Consider a signed value with a word length of 8, a fraction
length of 10, and a stored integer value of 5 (binary value `00000101`

).
The real-word value is calculated using the formula

```
RealWorldValue
= StoredInteger * 2 ^ -FractionLength
```

. In this case, ```
RealWorldValue
= 5 * 2 ^ -10 = 0.0048828125
```

. Because the fraction length
is 2 bits longer than the word length, the binary value of the stored
integer is `x.xx00000101`

, where `x`

is
a placeholder for implicit zeros. `0.0000000101`

(binary)
is equivalent to `0.0048828125`

(decimal). For
an example using a `fi`

object, see Create a fi Object With Fraction Length Greater Than Word Length (Fixed-Point Designer).

Computer hardware typically represents the negation of a binary fixed-point number in three different ways: sign/magnitude, one's complement, and two's complement. Two's complement is the preferred representation of signed fixed-point numbers and is the only representation used by Fixed-Point Designer.

Negation using two's complement consists of a bit inversion (translation into one's complement) followed by the addition of a one. For example, the two's complement of 000101 is 111011.

Whether a fixed-point value is signed or unsigned is usually not encoded explicitly within the binary word; that is, there is no sign bit. Instead, the sign information is implicitly defined within the computer architecture.