Verify OFDM Transmit and Receive using FPGA Data Capture
This example shows how to verify a wireless HDL IP that you generate in OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio). The example also shows how to monitor and analyze the internal signals of an IP core using FPGA data capture on real hardware.
You use the FPGA Data Capture tool to capture the hardware signals over JTAG for debugging analysis. FPGA data capture offers many capabilities to capture signals of interest using appropriate trigger and capture conditions. You validate the behavior of the
whdlOFDMRx Model subsystem in the
zynqRadioHWSWOFDMAD9361AD9364SL model by performing these steps.
Use capture control to capture valid data constellation points.
Use trigger conditions and multiple windows to capture header constellation points for frames with a failed CRC.
Use trigger conditions and the trigger position to capture synchronizing sequence (SS) correlation data for the peak search and validate the timing offset.
To run this example, you need a Xilinx Zynq ZC706 evaluation kit and FMCOMMS2/3/4 radio transmitter hardware.
Follow the steps in Guided Host-Radio Hardware Setup (Communications Toolbox Support Package for Xilinx Zynq-Based Radio) to configure the host computer and ZC706 board with FMCOMMS2/3/4 radio hardware.
Use the JTAG cable to connect the board to the host computer.
Simulink Model Setup
Mark the signals that you want to analyze through data capture as test points. To mark a signal as a test point, right-click the signal and then click Properties. On the Signal Properties dialog box, on the Logging and accessibility tab, select the Test point checkbox, as this figure shows.
Alternatively, use the
hOFDMTxRxAddTestPoints helper function to mark the required test points and save the model as
zynqRadioHWSWOFDMAD9361AD9364SLVerify. The function is attached to the example as a supporting file.
This figure shows the test points marked in the
whdlOFDMRx Model subsystem for capturing the header and data constellation points.
This figure shows the test points marked in the
Sync Signal Search subsystem for capturing the SS correlation and timing offset signals.
Generate HDL IP Core with Data Capture and Load Bitstream
Start the targeting workflow by right-clicking the
OFDM HDLsubsystem and selecting HDL Code > HDL Workflow Advisor.
In step 1.1, set Target workflow to
IP Core Generationand Target platform to
ZC706 and FMCOMMS2/3/4.
In step 1.2, set Reference design to
Receive and Transmit path. For this example, you can use the default values of the reference design parameters.
In step 1.3, select Enable HDL DUT output port generation for test points to update the interface table with all the test points. Then, in the Target platform interface table, map the test point signals to
FPGA Data Capture. For information about mapping IO ports, see OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio).
Run step 1.4 to step 3.1 by following the Generate IP Core section of the OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio) example.
In step 3.2, set FPGA data capture buffer size to
32768and FPGA data capture maximum sequence depth to
2. Select Include capture condition logic in FPGA Data Capture to insert the capture control logic into the generated FPGA data capture component, as this figure shows.
Run step 4.1 and follow the steps in the Generate Software Interface Model and Block Library section of the OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio) example to generate a software interface model.
To generate and download the bitstream onto the board, follow the Generate and Load Bitstream section of the OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio) example.
Alternatively, run the
hOFDMTxRxRunHDLWATasks helper function to run the tasks from step 1.1 to step 4.3. The function is attached to the example as a supporting file.
Capture and Analyze Data from IP Core
Capture the test points of the generated IP core and map them to FPGA data capture. To run the software interface model while the FPGA data capture waits for a trigger, launch the FPGA Data Capture tool in nonblocking mode.
cd(fullfile('hdl_prj','hdlsrc', ... 'zynqRadioHWSWOFDMAD9361AD9364SLVerify','fpga_data_capture')); fdc = FPGADataCapture; fdc.CaptureMode = 'nonBlocking'; fdc.launchApp;
Open the OFDM software interface model. Run the model in
Monitor & Tune mode to control the configuration from the Simulink model.
Capture Data Constellation Points
Use the frequency-domain, channel-equalized, and common-phase-error (CPE) corrected data subcarriers from the
Channel and CPE Estimation and Correction subsystem to plot the data constellation diagram. To capture only valid data constellation points, select Enable capture condition logic on the Capture Condition tab of the FPGA Data Capture tool and add
tp_dataValid_1 as a signal with value
High, as this figure shows. Click Capture Data.
After data capture is complete, plot the constellation diagram using the data that the board captures.
enableInternaLoopback in the software interface model is
false, the radio hardware transmits and receives the OFDM signals through the Tx and Rx antennas, respectively. The channel impairments modify the signal as it travels over the air in real time. In this scenario, use the constellation plot to analyze the received signal quality. You can also modify
modType in the software interface model and verify the data constellation diagram appears as you expect.
Capture Header Constellation Points for Failed CRC
When the signal-to-noise ratio (SNR) of the channel is low, the valid header data after channel equalization and CPE correction often has CRC failures. You can emulate these conditions using the software interface model.
In the software interface model, set
3. Use these trigger settings to capture the I/Q data of two header frames when the CRC fails.
Click Capture Data. If you have a DSP System Toolbox™ license, the Logic Analyzer app plots the captured data as multiple signal waveforms. The signal
tp_nSyncedFrames in the captured data indicates the number of the frame with a failed CRC.
Validate Functionality of
Sync Signal Search Subsystem
Sync Signal Search subsystem implements the SS correlation. The subsystem performs SS detection by continuously cross-correlating the received signal with the SS signal in the time domain. In addition, the subsystem computes the energy of the signal in the span of the correlator at each time step and then scales the value to generate a threshold value. The
Max Peak Searcher subsystem searches for the maximum correlation peak in each OFDM frame duration. In the
Sync Signal Search subsystem, the
SearchHold signal disables maximum peak search until it estimates the carrier frequency offset. The
SSPeakSearchDone signal goes high after the completion of peak search in each OFDM frame duration. For an FFT Length of 128, the frame duration is 5760 samples. The position of the maximum peak from the start of the frame duration gives the timing offset. You can capture valid samples of correlation in each OFDM frame duration to visualize the correlation data and record the timing offset.
On the Trigger tab, add
tp_searchHold_1 as a signal with the value
High in Trigger Stage 1. To capture correlation data for each frame duration, add
tp_SSPeakSearchDone_1 as a signal with the value
High in Trigger Stage 2 and set Trigger position to
5759. These settings ensure that the tool captures 5760 valid correlation samples before the signals satisfy these triggers. Samples 5761 to 11520 correspond to correlation of the next OFDM frame duration, and so on.
Select Enable capture condition logic on the Capture Condition tab to capture valid correlation data in each frame duration. Add the
tp_correlationValid_1 as a signal with the value
High, as this figure shows.
Click Capture Data. The Logic Analyzer displays the captured data as multiple signal waveforms.
hOFDMTxRxPlotSSCorrelation helper function to visualize the peak by plotting the captured correlation and threshold values. The index of the peak in each frame relative to start of the frame duration gives the timing offset.
This example shows how to map the internal signals of an IP core to FPGA data capture and then visualize the signals after you deploy the design to an FPGA. You use the trigger and capture control configuration of the FPGA Data Capture tool for capturing the signals of interest. You can use this approach to analyze and debug your own HDL IP core.
- OFDM Transmit and Receive Using Analog Devices AD9361/AD9364 (Communications Toolbox Support Package for Xilinx Zynq-Based Radio)