Clear Filters
Clear Filters

Activating on Linux without eth0

18 views (last 30 days)
Daniel Shub
Daniel Shub on 29 Apr 2013
Edited: Scott on 6 Jun 2016
I have an activation question. I have asked technical support, but I thought I would ask here. I thought this would be desirable both in terms of speed for me and potentially to share the issue for others ...
I run Arch Linux. Arch Linux has switched to the new standard of Consistent Network Device Naming where network devices are no longer named eth0, eth1, wlan0, wlan1. Both 1-661QJD and 1-EUTG50 are relevant and highlight the problem. For activation on Linux, TMW requires the legacy eth0 naming convention.
For Red Hat, TMW suggests removing the package that implements consistent network device naming. This is not an option on Arch. does anyone know a work around? Does anyone know a work around that does not require disabling consistent network device naming? I thought it used to be possible to activate with the UUID of a harddisk...
  5 Comments
Daniel Shub
Daniel Shub on 29 Apr 2013
Let me be clearer. I expected to find the controller in /dev (because I expect to find everything in /dev). A find / -name *enp0s25* where enp0s25 is the equivalent to eth0, turns up something in /sys/devices and /sys/class as well as a lot of entries in /proc/*. Are you suggesting I hardlink the /sys/devices entry?
Walter Roberson
Walter Roberson on 29 Apr 2013
Hmmm, apparently device files for ethernet have changed considerably ... I cannot find any on my OS-X system! I guess it must be using system calls to find the ethernet table. If something similar is what is happening on your system, then creating a new file might not help at all :(

Sign in to comment.

Accepted Answer

Daniel Shub
Daniel Shub on 29 Apr 2013
Edited: Scott on 6 Jun 2016
I asked a related question over at Unix and Linux.SE. Basically, for Linux the dummy kernel module will create a dummy network interface that you can then set the mac address of
modprobe dummy
ip l set dev dummy0 name eth0
ip link set dev eth0 address xx:xx:xx:xx:xx:xx
where xx:xx:xx:xx:xx:xx is the registered mac address/host id of the machine. I don't think that this violates the license agreement, although it is best to check.
I don't know the best way to make this persistent across reboots, but it shouldn't be too hard.
It might also be possible to simply rename one of the consistently named devices to eth0. This would eliminate the need for the dummy device and I believe the naming would still be consistent since you are always renaming the same device.
I have also been told that a udev rule can be used to revert back to ethX type naming. For machines that only have eth0 and/or wlan0 there is no advantage of consistent device naming since there is only one device. This means the udev rule does not hurt anything.
  1 Comment
Scott
Scott on 6 Jun 2016
Edited: Scott on 6 Jun 2016
Hi Daniel,
I am glad to hear you got MATLAB up and running on Arch using the instructions from Unix & Linux Stack Exchange. Just so you know, R2014a added support for Consistent Network Device Naming so these steps shouldn't be necessary for R2014a and later releases.
If you are unable to activate MATLAB normally using R2014a or later please contact us so we can look into this further:
Thanks,
-Scott
MathWorks Installation & Licensing Support

Sign in to comment.

More Answers (1)

A
A on 7 Sep 2013
Edited: A on 7 Sep 2013
I run Gentoo linux, and consistent NIC naming has been introduced since udev v197 I think. So activation was an issue for me as I had no eth0 device on my system.
My work-around was to create a udev rule to force the name eth0.
I have the following in /etc/udev/rules.d/70-use-eth0-for-matlab-licensing.rules (one line):
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="your:mac:address:here", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth?", NAME="eth0"
You can find the mac address of your device by running 'ifconfig -a'. Keep it in lower-case. I used my ethernet NIC's mac, as I hardly use it, so I'm hoping this won't have unintended consequences for the rest of my system.
You'll need to keep this work-around for as long as you use matlab (not just for activation), as the licensing info is verified at launch, so it needs to find eth0 every time.
You may have to update a /etc/init.d/net.* link and /etc/conf.d/net to use the new name.

Categories

Find more on Install Products in Help Center and File Exchange

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!